Manualsbrain.com
  1. Manuali
  2. Marche
  3. HP
  4. dx6120
  5. Manuale Utente

HP dx6120 Manuale Utente

Scarica
Pagina di 2
Keyboards (not illustrated)
PS/2, Basic
USB, Basic
USB, Basic (Blue Angel)
USB, Modular
355630-xxx
355631-xxx
355632-xxx
355102-xxx
Arabic [1]
-175
Greek [1]
-155
Portuguese [1, 3]
-135
Belgian
-185
Hebrew [1, 2]
-BB5
Russian [1]
-255
BHCSY[1, 2]
-B45
Hungarian [1]
-215
Slovakian [1]
-235
Czech [1]
-225
International [4]
-B35
Spanish [1, 3]
-075
Danish [3]
-085
Italian [3]
-065
Swedish [2, 3]
-105
Dutch [1]
-335
Japanese [1]
-295
Swiss [3]
-115
Europe [5]
-025
Kazak [1, 2]
-DF5
Taiwanese [1]
-AB5
Finnish [1]
-355
Korean (Hanguel) [1, 2]
-KD5
Thai [1]
-285
French [3]
-055
Norwegian [1, 3]
-095
Turkish [1, 3]
-145
French Arabic [1, 2]
-DE5
PRC [1]
-AA5
U.K. [1, 3]
-035
German [3]
-045
Polish [1]
-245
[1] Not for 355632-xxx
[2] Not for 355630-xxx
[3] Not for 355631-xxx
[4] Not for 355102-xxx
[5] Only for 355102-xxx
System Board Connectors and Jumpers (position of some untitled components may vary in location)
CR1
5V Aux power
P24
USB connector, front panel
E14
Boot block
P27
MultiBay
E49
Password jumper
P29
SCSI LED connector
J20
PCI slot 1
P52
Serial port “B”
J21
PCI slot 2
P54
Serial Port “A”
J31
PCI Express x1
P60
Primary Serial ATA (SATA) Port
J41
PCI Express x16
P61
Secondary Serial ATA (SATA) Port
P1
Main power (24 pin)
P124
Hood lock
P3
Processor VccP Power 12V (6 pin)
P125
Hood sensor
P5
Main power switch/LED 
SW50
CMOS button
P6
Internal chassis speaker
XBT1
Battery
P7
CD audio in
XMM1
Memory socket
P8
Primary chassis fan
XMM2
Memory socket
P9
Secondary chassis fan
XMM3
Memory socket
P10
Diskette drive
XMM4
Memory socket
P11
Aux audio in
XU1
Microprocessor
P20
IDE
XU100
Security
P23
Front audio
System Hardware Interrupts 
IRQ
System Function
IRQ
System Function
0
Timer Interrupt 
8
Real-Time Clock 
1
Keyboard
9
Unused
2
Interrupt Controller Cascade
10
Unused, available for PCI
3
Serial Port (COM B)
11
Unused, available for PCI
4
Serial Port (COM A)
12
Mouse
5
Unused, available for PCI
13
Coprocessor 
6
Diskette Drive
14
Primary ATA (IDE) Controller
7
Parallel Port (LPT 1)
Computer Diagnostic LEDs (on front of computer)
LED
Color
LED/Beep Activity
State/Message
Power
Green
On
(S0) Computer on
Power
Green
1 blink every 2 seconds
(S1) Suspend Mode
Power
Green
1 blink every 2 seconds
(S3) Suspend to RAM
Power
Clear
Off
(S4) Hibernation
Power
Clear
Off
(S5) Computer off
Power
Red*
2 blinks 1 second apart
CPU thermal shutdown
Power
Red*
3 blinks 1 second apart
CPU not installed
Power
Red*
4 blinks 1 second apart
Power supply overload (crow bar)
Power
Red*
5 blinks 1 second apart
Defective or missing memory
Power
Red*
6 blinks 1 second apart
Defective or missing graphics
Power
Red*
7 blinks 1 second apart
System board failure (detected prior to video)
Power
Red*
8 blinks 1 second apart
Invalid ROM based on bad checksum
Power
Red*
9 blinks 1 second apart
System not fetching code
Power
Red*
10 blinks 1 second apart
System hang while loading an option ROM
Hard Drive
Green
Blinking
Hard drive activity
*Blinking codes are repeated after a 2 second pause. Beeps stop after fifth iteration but LEDs continue until problem is 
resolved.
Keyboard Diagnostic LEDs, PS/2 Keyboards Only
LED
Color
LED Activity
State/Message
Num, Caps, 
Scroll Lock
Green
On (Rising Tone)
ROM reflashed successfully
Num Lock
Green
On
ROMPaq diskette not present, is bad, or drive 
not ready.*
Caps Lock
Green
On
Enter password.
Num, Caps, 
Scroll Lock
Green
Blink On in sequence, one at a 
time - N, C, SL
Keyboard locked in network mode
* Insert valid ROMPaq diskette in drive A. Turn power switch off, then on to reflash ROM. If ROM flash is successful, all 
three keyboard LEDs will light up, and you will hear a rising tone series of beeps. Remove diskette and turn power off, 
then on to restart the computer. For more information about flashing the ROM, refer to the Troubleshooting guide.
Clearing CMOS
The computer's configuration (CMOS) may occasionally be corrupted. If it is, it is necessary to clear the CMOS 
memory using switch SW50.
To clear and reset the configuration, perform the following procedure:
1.
Prepare the computer for disassembly.
Ä
CAUTION: The power cord must be disconnected from the power source before pushing the Clear CMOS 
Button (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board.
2.
Remove the access panel.
3.
Press the CMOS button located on the system board and keep it depressed for 5 seconds.
4.
Replace the access panel.
5.
Turn the computer on and run F10 Computer Setup (Setup utility) to reconfigure the system.
Disabling or Clearing the Power-On and Setup Passwords
1.
Turn off the computer and any external devices, and disconnect the power cord from the power outlet.
2.
Remove the access panel.
3.
Locate the header and jumper labeled E49.
4.
Remove the jumper from pins 1 and 2. Place the jumper over pin 2 only to avoid losing it.
5.
Replace the access panel.
6.
Plug in the computer and turn on power. Allow the operating system to start. 
NOTE: Placing the jumper on pin 2 clears the current passwords and disables the password features.
7.
To re-enable the password features, repeat steps 1-3, then replace the jumper on pins 1 and 2.
8.
Repeat steps 5-6, then establish new passwords.
Refer to the Computer Setup (F10 Setup) instructions to establish new passwords.
Computer Setup (F10) Utility Features (features may vary)
File
System Information
About
Set Time and Date
Replicated Setup
Default Setup
Apply Defaults and Exit
Ignore Changes and Exit
Save Changes and Exit
Storage
Device Configuration
Storage Options
DPS Self-Test
Boot Order
Security
Setup Password
Power-On Password
Password Options
Smart Cover
Embedded Security
Drivelock Security
Data Execution Prevention
Master Boot Record Security
Save Master Boot Record
Restore Master Boot Record
Device Security
Network Service Boot
System IDs
Power
OS Power Management
Hardware Power Management
Thermal
Advanced
Power-On Options
BIOS Power On
Onboard Devices
PCI Devices
Bus Options
Device Options
PCI VGA Configuration