Manualsbrain.com
  1. Manuali
  2. Marche
  3. Honeywell
  4. HD60
  5. Manuale Utente

Honeywell HD60 Manuale Utente

Scarica
Pagina di 1
READ AND KEEP THIS
OPERATION MANUAL
   
   
   
  
  
  
  
  
  
  
  
  
•S
im
ple  to insta
ll
Operation
Manual
• 1/3" Sony Super HAD CCD
• 380 TV Lines Resolution
• 4mm Fixed Lens
• Color Day/Night with 24 LEDs
• Auto White Balance
• AGC, BLC, Flickerless On/Off
• Extra Video Output for Installer
• 3-Axis Camera Construction
• Diameter of Bubble : 100mm
HD60
Series
SPECIFICATIONS:
DIMENSIONS(mm):
Model
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
BLC
Flickerless
Input / Output Connector
Power Consumption
Dome Size (Ø)
Weight
NTSC                                    PAL
NTSC : 525 Lines                        PAL : 625 Lines 
2 : 1 Interlace
 15.734kHz                                 15.625kHz
 59.94Hz                                       50Hz  
1/3" SONY Super HAD CCD
  270K / 250K                               320K / 290K 
More than 48dB (AGC Off)
380 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens : f=4.0mm, 81º
Manual
Internal
0 Lux, IR LED
1/60 ~ 100,000 Sec.                  1 /50 ~ 100,000 Sec.
Auto
On / Off
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video
12VDC (10.8V~15V), 0.4A / 5W (Max)
100mm
Approx. 366g
You must be fully aware of all the distinctive 
features and precautions related to this 
camera before installing it.
    Built-in             camera 
bracket makes it much 
easier to rotate in any 
direction.
3-axis
CAMERA SET-UP:
Fixed Lens & IR LED Type
     CAUTION : When AGC is off, 
      D/N does not work because the 
      D/N switching function is 
      dependent on the AGC level.
Function Selection Switch: 
•FL(Flickerless) ON/OFF
•AGC(Auto Gain Control) ON/OFF
•BLC(Back Light Compensation) 
  ON/OFF
Service Monitor Connecter: 
Use service monitor connector
to set camera angle & focus
when installing.
a
b
The image does not 
appear on the screen.
Check the power source for the monitor and camera 
and ensure that the voltage and polarity are properly 
connected and being supplied correctly.
The image on the 
screen is dim.
Check if the lens is stained. If dirty, clean the lens with 
a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not work 
properly, the surface of the 
camera case is hot, and a black 
line appears on the screen.
Check if you have connected the camera to a proper 
power source and If there is no problem with the power, 
turn the unit off immediately and seek assistance from 
our Customer Service department.
The screen blinks a lot.
Check if the camera is pointed toward the sun or a 
fluorescent lamp.
Adjust the angle or location of the camera if too much 
light is coming into the screen.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following. 
 If the guidelines do not enable you to solve the problem, contact an authorized technician.
NAME AND FUNCTION:
Fixed Lens & IR LED Type
BLC
AGC
FL
ON
OFF
ON
DC LEVEL
VIDEO
SWITCH
ON
3
1
2
AC 24V
J503
J504
AC24V
J501
J502
HE
AT
ER
/AUD
IO
J5
05
b
a
P/N:3810-0072H
Rev 0 03
/18
!
Do not install the camera in 
extreme temperature conditions.
Do use the camera under conditions where 
temperatures are within -10°C to 45°C. 
Be especially careful with ventilation 
under high temperatures.
!
Do not install or use the camera 
in an environment where the 
humidity is high.
It can cause the image quality to be poor.
!
Do not drop the camera or 
subject them to physical shocks.
It can cause malfunctions to occur.
!
Do not disassemble the camera.
There are no user-serviceable parts 
inside it.
!
Note
When this camera is installed near 
wireless communication devices 
that emits strong electromagnetic 
field, irregularity such as noise on 
the monitor may appear. 
PRECAUTIONS:
CONNECTION:
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
12VDC(10.8V~15V), 0.4A/5W(Max)
Terminal Color
Yellow
Red
Connecting to 
Monitor and Power
12VDC Power Type
Camera Lay-out
#1
#2
Video
(Yellow)
Power - 12VDC
(Red)
Video Output
GND
• The wire is polarized.   • Use 12VDC     power source.
360º
360º
90º
Design and specifications are 
subject to change without notice.
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
www.honeywellvideo.com
Tilt rotation:
 
Adjusting the vertical angle.
Pan rotation:
 
Adjusting the horizontal angle.
Horizontal rotation: Adjusting the horizontal 
                                position of the screen.
1
2
3
IR LED: 850nm / 30°(24EA)
Sensor
4
5
• Power Consumption: 5W
• IR LED Specification: 850nm / 30°(24EA)
IR LED (4mm Fixed Lens)
1
2
3
4
5
51.0
75.7
37.3
13.7
100.0
130.6
102.0
COMPOSITION:
INSTALLATION:
Draw out power / video wires 
to the connecting places.
3
Stick the guide pattern on the 
wall or ceiling.
1
Adjust desired focus and scene 
by turning and moving the 
3-axis camera bracket by hand.
5
Drill four holes according to
the guide pattern then insert
anchors into the drilled holes.
2
Put the dome cover over the 
base.
6
Fix the dome cover on the base 
by covering.
7
Fixed the camera to a celling
using four screws.
4
Insert coin to the side 
hole and remove the 
dome cover by twist coin.
NOTE
Operation Manual
Guide Pattern
Service Monitor Cable
Mounting Screw
Dome Cover
Guide Pattern
Dome Base
Mounting 
Screw
Ceiling