Sony ta-va777es Manuale Utente
25
GB
Location of Parts and Basic Operations
!™ EQ BANK button
Press repeatedly to select an equalizer (EQ PRESET
1~5) or turn the equalizer off (EQ PRESET OFF).
1~5) or turn the equalizer off (EQ PRESET OFF).
z
To maintain the highest fidelity to the original source
Do the following to bypass the sound field and equalizer circuits.
1 Press EQ BANK to turn off the equalizer.
2 • When listening to multi-channel sources, press A.F.D. to turn
1 Press EQ BANK to turn off the equalizer.
2 • When listening to multi-channel sources, press A.F.D. to turn
off the sound field processing.
• When listening to two channel (stereo) sources, press 2 CH to
bypass the sound field processing.
The result will be a sound that is highly faithful to the program
source.
source.
!£ MASTER VOLUME control
After turning on the component you selected, turn to
adjust the volume.
adjust the volume.
!¢ OPEN/CLOSE buttons
Press to open/close the door on the front panel.
Note
The door may suddenly stop if an external force is applied
while it is being opened or closed. When this occurs, do not
attempt to open or close the door by hand. Remove the cause
of the force, then press OPEN/CLOSE again.
If the door stopped while being closed, the door
automatically opens again a few seconds after closing. If the
door stopped while being opened, the door remains where it
stopped.
while it is being opened or closed. When this occurs, do not
attempt to open or close the door by hand. Remove the cause
of the force, then press OPEN/CLOSE again.
If the door stopped while being closed, the door
automatically opens again a few seconds after closing. If the
door stopped while being opened, the door remains where it
stopped.
!∞ ENTER button
Press to enter the index name (page 45) and clear
settings.
settings.
!§ Cursor buttons ( / )
Press to select various speaker level, surround, and
equalizer parameters (etc.).
equalizer parameters (etc.).
!¶ Jog dial
Turn to adjust the selected speaker level, surround,
and equalizer parameters (etc.).
and equalizer parameters (etc.).
!• SET UP button
Press to activate the setup mode, then use the cursor
buttons (!§) to select the parameters. You can then
make various settings using the jog dial (!¶).
buttons (!§) to select the parameters. You can then
make various settings using the jog dial (!¶).
!ª LEVEL button
Press to activate the speaker level parameters (page
33). You can adjust the various speaker level
parameters (front balance, rear balance, etc.).
33). You can adjust the various speaker level
parameters (front balance, rear balance, etc.).
@º CUSTOM button
Press to activate custom parameters (page 33).
@¡ SUR button
Press to activate the surround parameters (page 33).
You can adjust the various surround parameters (effect
level, wall type, etc.).
You can adjust the various surround parameters (effect
level, wall type, etc.).
@™ NAME button
Press to activate the name function and enter names
for program sources (page 45).
for program sources (page 45).
@£ EQ button
Press to activate the equalizer parameters (page 33).
You can adjust the various equalizer parameters.
You can adjust the various equalizer parameters.
@¢ SPEAKERS selector
Set according to the front speakers you want to drive.
Set to
To select
A
The speakers connected to the FRONT
SPEAKERS A terminals
SPEAKERS A terminals
B
The speakers connected to the FRONT
SPEAKERS B terminals
SPEAKERS B terminals
A+B*
The speakers connected to both the FRONT
SPEAKERS A and B terminals (parallel
connection)
SPEAKERS A and B terminals (parallel
connection)
OFF
No speaker output
*
Be sure to connect front speakers with a nominal impedance of 8
ohms or higher if you want to select both sets (A+B) of front
speakers
ohms or higher if you want to select both sets (A+B) of front
speakers
PHONES jack
Use to connect stereo headphones.
Connecting headphones cuts the output from the PRE
OUT jacks and speaker terminals.
When the headphones are connected, if 2 CH or
AUTO FORMAT DECODING is selected, 2 channel
stereo is output. If any other sound field is selected, it
is automatically changed to “HEADPHONE
THEATER”.
Use to connect stereo headphones.
Connecting headphones cuts the output from the PRE
OUT jacks and speaker terminals.
When the headphones are connected, if 2 CH or
AUTO FORMAT DECODING is selected, 2 channel
stereo is output. If any other sound field is selected, it
is automatically changed to “HEADPHONE
THEATER”.