Panasonic cy-vm7203n Manuale Utente

16

17

15

16

Press [SRC/PWR] to change the source.

 AV 

 VIDEO 

1 

 VIDEO 

2 

Preparation: 
 Connect an optional external device to the unit.

Note:
 When the Rear View Camera is in operation with the 

transmission gear shift in the reverse position, the 
image is shown on the “FULL” screen only.

 In some cases, the picture looks different from the 

original one due to your selection of aspect.

Default: NORMAL
Mode: 4 types

Press [ASP] (ASPECT) on the display unit to change the 
aspect ratio as follows.

NORMAL
 The conventional display image 

has a 4 to 3 ratio of horizontal 
to vertical.

 In this case, a blank area 

remains on the right and left 
sides of the display. 

FULL
 The screen is extended 

horizontally as a whole to the 
aspect ratio of 16 to 9.

 The extension ratio is the same 

at any point of the screen.

ZOOM
 The screen is fully extended at 

the normal aspect ratio of 4 to 
3.

 The top and bottom of the 

screen are slightly cut.

CINEMA 
 The display is only zoomed 

vertically.

 The top of the screen will be 

cut off, but the bottom will not 
be.

 This is to remind you that compression or extension 

of the screen using the aspect ratio (screen mode) 
changing function of this product for commercial 
purpose of profi t making or viewing/listening by 
the public could infringe on the rights of the author 
protected by the copyright law.

 If you expand normal picture (4 to 3) by using 

“CINEMA”, “ZOOM” or “FULL” aspect to the full 
of the screen, you might not see the periphery of 
the picture, or you might see a distorted picture. 
Therefore, use the “NORMAL” mode to see the 
original pictures as the author intended it.

Preparation: 
 Specify the correct terminal that is connected to the car 

navigation system in the “NAVI INPUT” operation on 
the “User Settings (USER)”. (page 20)

Press [NAVI] to change to the car navigation source.
Press [NAVI] again to cancel. 

Note: 
 If the navigation source is ON, only the audio signal is 

switched while the video signal remains as it is and the 
image is shown on the “FULL” screen only. 

 The source can be changed even when the display unit 

is in the retracted position. 

Select AV source. 
Connect a Panasonic TV tuner to AV-IN connectors. 
(page 35) 

Recommended source: VIDEO 1
Select the same source (VIDEO 1 or VIDEO 2) as the 
terminal that is connected to a DVD player or camcorder 
(VIDEO 1-IN or VIDEO 2-IN). 

Recommended source: VIDEO 2 
Select the same source (VIDEO 1 or VIDEO 2) as the 
terminal that is connected to a Rear View Camera 
(VIDEO 1-IN or VIDEO 2-IN). 
 Execute “CAMERA SETUP” (Rear View Camera Setup) 

setting. (page 20) 

Source display 

See “Car Navigation System” below. 
Connect a Panasonic Car Navigation System to RGB 
connector. (page 34) 

Note: 
 Car Navigation System (CN-DV2300N, option) is not for 

sale in some countries and regions.

Select the same source (VIDEO 1 or VIDEO 2) as the 
terminal that is connected to a Car Navigation System 
(VIDEO 1-IN or VIDEO 2-IN). 
 Execute “NAVI INPUT” (Navigation Input Selection) 

setting. (page 20) 

[SRC/PWR] (Source)

[SRC] (PWR) 
(Source)

[NAVI] (Navigation)

VIDEO 1-IN: 
DVD player/receiver 
(CQ-D5501N, option)

VIDEO 2-IN: 
Rear View Camera

AV-IN: 
TV tuner (CY-TUP153N, option)

RGB: 
Panasonic Car Navigation System 
(CN-DV2300N, option)

