Panasonic dmr-e75veb Manuale Utente
Connection and Set up
15
In some cases, interference (lines or patterning) or a very poor
picture may appear on the TV when the DVD Video Recorder is
connected. If this happens, follow the steps below to change
the video playback channel (RF output channel) to remove the
interference.
picture may appear on the TV when the DVD Video Recorder is
connected. If this happens, follow the steps below to change
the video playback channel (RF output channel) to remove the
interference.
[1]
Press [FUNCTIONS] for more than 5 seconds.
The RF output channel number is displayed on the unit display.
[2]
Press the numeric buttons, [
3, 4] or [CH, W, X]
to select a channel number, which differs by
2 or 3 from the present channel number.
2 or 3 from the present channel number.
≥(For example, if the original channel number was 28, enter 31.)
≥Set the RF output channel of the DVD Video Recorder to [ss]
(RF OFF) when the DVD Video Recorder is connected to the
TV via the 21-pin Scart cable.
Press the numeric (0) button
or [CH,
TV via the 21-pin Scart cable.
Press the numeric (0) button
or [CH,
W, X] to display [ss].
Skip the step 4, if using a
21-pin Scart cable.
21-pin Scart cable.
[3]
Retune your TV until you receive the Test
pattern.
pattern.
≥It may be necessary to repeat steps 1 and 2 above until you
can see the Test pattern clearly.
[4]
Press [ENTER] to finish this setting.
This unit is not designed to control (switch on or change channel)
your satellite receiver or Cable TV box, however, it can be taught to
recognise VIDEO Plus+ Codes for Satellite stations. The Satellite
receiver or Cable TV box must be switched on and the correct station
selected. Some receivers have their own timer facility for this
purpose. Please refer to your Satellite Receiver/Cable TV box
instructions for use of such timer facilities.
your satellite receiver or Cable TV box, however, it can be taught to
recognise VIDEO Plus+ Codes for Satellite stations. The Satellite
receiver or Cable TV box must be switched on and the correct station
selected. Some receivers have their own timer facility for this
purpose. Please refer to your Satellite Receiver/Cable TV box
instructions for use of such timer facilities.
For your unit to recognise the VIDEO Plus+ Codes for each satellite
station, you must teach your unit which channel or AV input to record
from for the first time. Otherwise when setting a VIDEO Plus+
recording, the [
station, you must teach your unit which channel or AV input to record
from for the first time. Otherwise when setting a VIDEO Plus+
recording, the [
ss] symbol will appear in the channel position
indicating that the unit does not know which channel position to set.
Once you have set the channel/AV input once the unit will remember
it whenever you use a VIDEO Plus+ Code for the station again.
Once you have set the channel/AV input once the unit will remember
it whenever you use a VIDEO Plus+ Code for the station again.
[1]
Press [VIDEO Plus+].
[2]
Enter a VIDEO Plus+ Code from a Satellite TV
Guide for a satellite channel, e.g. Sky 1 using
the numeric buttons.
Guide for a satellite channel, e.g. Sky 1 using
the numeric buttons.
≥If you make a mistake, use [2] to go back.
[3]
Press [ENTER]. [
ss] will appear instead of a
channel number/AV input.
[4]
Use [
3, 4, 2, 1] to select the channel or AV
input that is to be used for recording from the
satellite channel.
satellite channel.
[5]
Press [ENTER]
to memorise the
setting.
to memorise the
setting.
≥The unit will now
automatically set the
programme position
or AV input correctly
when a VIDEO Plus+ recording is set for this satellite station in
the future.
programme position
or AV input correctly
when a VIDEO Plus+ recording is set for this satellite station in
the future.
[6]
Use [
3] to
select the
programme that
you have just
set.
programme that
you have just
set.
≥Now press
[
¢, CANCEL/RESET] to delete it from the timer recording list.
It is no longer needed.
[7]
Repeat steps 1
s6 above until you have set and
deleted dummy timer recordings for each of the
satellite stations that you will make VIDEO
Plus+ recordings from.
satellite stations that you will make VIDEO
Plus+ recordings from.
[8]
Press [RETURN] when you have finished.
Removing Interference
Preparation
≥Press [DVD].
≥Press [DVD].
TV screen
The picture with interference
Unit display
Indication when the RF output
channel is 28 (example)
channel is 28 (example)
Test pattern indication
Indication after changing the RF
output channel to 31 (example)
output channel to 31 (example)
Unit display
Test pattern indication
<Before Changing>
<After Changing>
RF OUTPUT CHANNEL
DVD
CH : 31
RETURN
SELECT
ENTER
RF OUTPUT CHANNEL
DVD
CH : 28
RETURN
SELECT
ENTER
21
68
(RF OFF)
...
The clear picture
VIDEO Plus+ Codes for Satellite
Receivers/Cable TV
Receivers/Cable TV
Preparation
≥Turn on the TV and the unit. Select video playback channel
≥Turn on the TV and the unit. Select video playback channel
on the TV.
≥Press [DVD].
VIDEO Plus+
4:11 LP
Remain
15. 7. TUE
12:53:00
Mode
Stop
Start
Name
Date
TIMER
RECORDING
RECORDING
PDC
Remain
4:00 LP
Programme Name
13. 7. TUE
12:53:00
AV2
15/7 TUE 20:00 21:00 SP
TIMER
RECORDING
RECORDING
Remain
4:00 LP
SP
OK
21:00
20:00
AV2
01
Mode
Disc
space
Stop
Start
No.
Name
Date
New Timer Programme
PDC
13. 7. TUE
12:57:00
15/ 7 TUE
EB.book 15 ページ 2004年4月13日 火曜日 午前9時7分