Panasonic sa-ht1000 Manuale Utente
9
RQT7061
INT
R
O
STEP
1
Plug-in Auto Tuning
After plugging the unit into your household AC outlet and pressing
[
[
Í POWER] to turn the unit on for the first time, the unit assists you
to set the menu language, and automatically tunes in all the
channels it can receive and sets the clock.
channels it can receive and sets the clock.
The unit automatically determines the type of transmission
(airwaves or cable) and puts them into channels as follows.
(airwaves or cable) and puts them into channels as follows.
Preparation
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the appropriate video input to
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the appropriate video input to
suit the connections to this unit.
≥Press [DVD] to select “DVD/CD” as the source.
1
Press [
Í POWER] to turn the unit on.
2
Press [
3, 4] to select the menu
language and press [ENTER].
3
Press [ENTER] to start Plug-in Auto
Tuning.
Tuning.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished. If the clock is an hour slower or
faster than the actual time, go to “Time Zone Adjust” to
correct it (
displayed when finished. If the clock is an hour slower or
faster than the actual time, go to “Time Zone Adjust” to
correct it (
➡page 43).
4
When the display shows the correct time
Press [ENTER] to complete Plug-in
Auto Tuning.
Auto Tuning.
∫ If the unit couldn’t set the clock automatically
Press [ENTER] to show the “Manual Clock Setting” screen. Set the
time manually (
time manually (
➡page 43).
∫ To start Plug-in Auto Tuning again (after
relocation, for example)
When the unit is on and stopped
1 Press and hold [
1 Press and hold [
X CHANNEL] and [W CHANNEL] on the
main unit for about five seconds.
The unit turns off.
The unit turns off.
2 Press [
Í POWER] to turn the unit on.
Follow the above steps 2–4.
∫ If Plug-in Auto Tuning fails (
➡page 40, Antenna
System and Auto Channel Setting)
Add or delete channels if necessary channels are not set or
unnecessary channels are set.
unnecessary channels are set.
While this unit is receiving the antenna signal (but not during
recording):
recording):
1
Press the numbered buttons to select
a channel.
a channel.
e.g., “5”: [0]
➡ [5]
“15”: [1]
➡ [5]
“115”: [100]
➡ [1] ➡ [5]
≥You can also use [W X CH] when you
are going to delete a channel.
2
Press [ADD/DLT].
The channel is deleted if it was set or added if it was not set.
e.g.,
e.g.,
Repeat steps 1 and 2 as necessary.
Band
Channel
TV Mode
(Airwaves)
(Airwaves)
VHF
2–13
UHF
14–69
CATV Mode
(Cable)
(Cable)
VHF
2–13
CATV LOW BAND
95–99
CATV MID/SUPER BAND
14–36
CATV HYPER BAND
37–65
ULTRA BAND
66–94
100–125
SPECIAL CATV CHANNEL
1
CH
VOLUME
SKIP
STOP
PAUSE
PLAY/x1.3
SLOW/SEARCH
CANCEL
1
2
3
4
5
6
7
8
9
0
100
HOME THEATER
TV
STATUS
MULTI REAR
MARKER
S.POSITION
F.Rec
C.FOCUS
REC MODE
CH SELECT
RETURN
P.MEMORY
EQ/SFC
ERASE
ADD/DLT
PROG/CHECK
L1/OPT
FUNCTIONS
TOP MENU
ENTER
DIRECT NAVIGATOR
MENU
PLAY LIST
MIX
2CH
FRAME
REC
TEST
CM SKIP
SETUP
MUTING
AUDIO
S W. LEVEL
FM/AM
TV/VIDEO
INPUT SELECT
OPEN/CLOSE
DISPLAY
DVD
VCR Plus+
POWER
POWER
PRO LOGIC
TIME SLIP
SHIFT
SHIFT
3, 4, 2, 1
ENTER
ADD/DLT
Í POWER
W X CH
DVD
DOWN
TIME SLIP
REC
ERASE
MEMORY
FM/AM
DVD
REC MODE
FM MODE
UP
VOLUME
OPEN/CLOSE
TUNING
TIME SLIP
CHANNEL
PHONES
POWER
DVD
X, W CHANNEL
Numbered
buttons
buttons
Antenna system, channel caption, and VCR Plus
r guide
channel settings all revert to the default values when you
perform the procedure below. Timer recording settings are
also cleared.
perform the procedure below. Timer recording settings are
also cleared.
Adding and deleting channels
English
Español
Français
Press ENTER
Pulse ENTER
Pulse ENTER
Appuyer sur ENTER
Select Language
Seleccione la Lengua
Sélection de Langue
Auto Channel Setting
CH.
Auto Channel Setting
Proceeding . . .
1
1 1
1
CH
Unit’s display
CHANNEL 15 DELETED
7061en.book 9 ページ ２００３年７月１日 火曜日 午前１１時４４分