Panasonic sa-ht1500 Manuale Utente

38

RQT7619

You can make the sound of the center speaker seem 
like it is coming from within the television.

r[C.FOCUS].

Each time you do this:
CENTER FOCUS ON

>CENTER FOCUS OFF

 ^------------"-------------""-"""""---=}

≥This will have less effect when Dolby Pro Logic II 

is turned on.

≥This doesn’t work when “SFC” is lit on the display.

This mode is useful if you have to place your 
surround speakers near the front speakers 
due to the layout of your room.
This mode makes it seem like the sound from 
the surround speakers is coming from behind 
you.

r[MULTI REAR] for 

Each time you do this:

V.R.S ON

!)

V.R.S OFF

This mode makes it seem like sound is coming 
from multiple rear surround speakers virtually 
when connected with surround speakers.

r[MULTI REAR].

Each time you do this:

M.R.S ON

!)

M.R.S OFF

Using this function makes you feel like you are sitting 
in the ideal seating position (in the center of the circle 
formed by the speakers), even if you cannot due to 
the layout of your room.

r[S.POSITION].

3, 4, 2,  1] to select a position.

To cancel
Press [SHIFT]

r[S.POSITION] again.

[Note]

≥This doesn’t work when “SFC” is lit on the display.
≥While virtual rear surround is on, the seat position is changed in three horizontal steps.

Each time you press the button:
SUB W 1

>SUB W 2>SUB W 3>SUB W 4 (factory preset)

 ^-------------------------------------------------------------}

≥This doesn’t work when “SFC” is lit on the display.

Adjust the level of the speakers so they are the same apparent level 
as the front speakers where you would normally be sitting and 
listening. (L, R 

➡below, Balance)

Preparation
≥Dolby Digital and DTS: Turn off the other sound field systems.
≥Dolby Pro Logic II: Press [SHIFT]i[ÎPRO LOGIC II].

r[TEST] to output a test signal.

Lch: Front left

RSch: Right surround

Cch: Center

LSch: Left surround

Rch: Front right

r] or [s] to set the volume level normally 

3] (to increase) or [4] (to decrease).

L, R: (

➡below, Balance)

C, RS, LS: 

j6 dB to i6 dB

To stop the test signal, press [SHIFT]

i[TEST] again.

∫ To adjust speaker level during play

(This doesn’t work when “SFC” is lit on the display.)
1 Press [SHIFT]

r[CH SELECT] to select the speaker. 

L

R

>Cch>RSch>LSch>SWch

^---------------------------------------------------}

SW: Subwoofer
≥You can only adjust SW if there is output from the subwoofer channel.

3] (to increase) or [4] (to decrease).

L, R: (

➡below, Balance)

C, RS, LS:

j6 dB to i6 dB

SW: 

j6 dB to i6 dB

You can adjust the balance of the front speakers.
1 Press [SHIFT]

r[CH SELECT] to select “L R”.

2, 1] to adjust the “L”, “R” balance.

–multi-channel discs
–2-channel discs with Dolby Pro Logic II on

–multi-channel discs
–2-channel discs with Dolby Pro Logic II on

Virtual speakers

Virtual speakers

–multi-channel discs
–2-channel discs with Dolby Pro Logic II on

7619en.book  38 ページ  ２００４年５月６日　木曜日　午前９時３３分