Panasonic sb-tp55eb Manuale Utente
RQT6905
3
;
;
;
;
;
y
y
270 mm
30-35 mm
ø7.5-9.5 mm
7-9 mm
10 mm
60 mm
Speaker setup
Take care when handling the speakers not to apply undue pressure
to the front nets. Lay the speakers on a flat surface over a soft cloth
when working on them.
Tighten the screws firmly.
to the front nets. Lay the speakers on a flat surface over a soft cloth
when working on them.
Tighten the screws firmly.
Front and surround speakers (SB-FS50)
The 4 speakers are the same.
Put the front speakers either side of the television. Put the surround
speakers to the side of or slightly behind the seating area.
Put the front speakers either side of the television. Put the surround
speakers to the side of or slightly behind the seating area.
Do not attach these speakers to walls or ceilings.
Attaching the base
Screw for base
Place with the net up.
Refitting the stabilizer
Refit the stabilizer if you place the speaker so that there are more
than 20 cm between its rear and a wall.
than 20 cm between its rear and a wall.
Unscrew the four screws.
Turn the stabilizer around and reattach with the four screws.
Turn the stabilizer around and reattach with the four screws.
Adjusting height
There are three heights (approx. 1108 mm, 1170 mm, and 1284
mm).
The speakers are shipped at the lowest height.
Unscrew the screw (
) and detach the casing.
Unscrew the four screws and detach the stand.
Change the position of the stand and reattach with the four
Change the position of the stand and reattach with the four
screws.
Hooks
Do not pinch the speaker cord.
Do not pinch the speaker cord.
Reattach the casing and fix with the screw.
Attaching a stabilizing wire
Example
Nylon clamp
Screw for nylon clamp
Wire (not included)
Ring (not included)
Screw (not included)
Screw for nylon clamp
Wire (not included)
Ring (not included)
Screw (not included)
Screw the wood screw into a thick and hard part of the wall.
The surface must be able to support over 30 kg.
The surface must be able to support over 30 kg.
Center speaker (SB-PC50)
Put above or below the center of the television, on a shelf or rack or
attach to the wall. Placing it directly on the television can cause the
picture to be distorted.
attach to the wall. Placing it directly on the television can cause the
picture to be distorted.
Do not attach this speaker to walls or ceilings using methods other
than those described here.
than those described here.
Attaching the rubber feet when placing on a surface
Attach the rubber feet to the base of the speaker to prevent vibration
from causing the speaker to move or fall over.
from causing the speaker to move or fall over.
Attaching to a wall
Attach four rubber feet to the rear of the speaker.
Screw (not included)
Screw the wood screw into a thick and hard part of the wall.
The surface must be able to support over 10 kg.
The surface must be able to support over 10 kg.
Attaching to a television stand
Ensure the following conditions are met when purchasing or prepar-
ing your television stand.
Observe the diameter and length of the screws and the distance
between the screws as shown in the diagram.
ing your television stand.
Observe the diameter and length of the screws and the distance
between the screws as shown in the diagram.
Television stand (not included)
Screw (not included); diameter: 5 mm, pitch: 0.8 mm, length:
Screw (not included); diameter: 5 mm, pitch: 0.8 mm, length:
thickness of board plus 10 mm.
Distance between the centers of the holes: 60 mm.
The stand must be able to support over 10 kg.
Subwoofer (SB-WA55)
Place anywhere as long as it is a reasonable distance from the tele-
vision. Place it at least 5 cm from the wall as it has a bass reflex port
in the rear.
vision. Place it at least 5 cm from the wall as it has a bass reflex port
in the rear.
Do not attach this speaker to walls or ceilings.