Panasonic sa-ht822v Manuale Utente
44
RQT7708
The radio
Press [TUNER] to put the remote control in TUNER mode.
Up to 15 stations can each be set in the FM and AM bands.
1
Press [FM/AM] to select “FM”.
2
Press [
6] or [5] to tune to the
lowest frequency (“FM 87.9” MHz or
“FM 87.5” MHz).
“FM 87.5” MHz).
3
Press and hold [ENTER].
Release the button when “AUTO” is displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
≥“SET OK” is displayed when the stations are set. The last
channels in ascending order.
≥“SET OK” is displayed when the stations are set. The last
station to be set is then played.
4
Repeat steps 1 to 3 to set the AM
bands (the lowest frequency is
“AM 520” kHz).
bands (the lowest frequency is
“AM 520” kHz).
1
Press [FM/AM] to select “FM” or
“AM”.
“AM”.
2
Press [
6] or [5] to select the
frequency.
Press and hold [
6] or [5] until the frequency starts
scrolling to start automatic tuning. Tuning stops when a station
is found.
is found.
1
Tune to the station (
➜ above).
2
Press [ENTER].
3
While “PGM” is flashing on the display
Press the numbered buttons to select
a channel.
a channel.
Alternatively, press [
W CH] or [X CH] then press [ENTER].
The station occupying a channel is erased if another station is preset
to that channel.
to that channel.
1
Press [FM/AM] to select “FM” or “AM”.
2
Press the numbered buttons to select
the channel.
the channel.
Alternatively, press [
W CH] or [X CH].
To select a 2-digit number
e.g. 12: [
e.g. 12: [
S10]
➜ [1] ➜ [2].
When a stereo FM broadcast is being received.
∫ If noise is excessive in FM
Press [PLAY MODE] to display “MONO”.
Press [PLAY MODE] again to cancel the
mode.
The mode is also canceled when you
change the frequency.
mode.
The mode is also canceled when you
change the frequency.
∫ FM frequency step
Main unit only
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated in 0.1-MHz steps.
1 Press [INPUT SELECTOR]
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated in 0.1-MHz steps.
1 Press [INPUT SELECTOR]
on the main unit to select “FM”.
2 Press and hold [INPUT SELECTOR].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
procedure. Preset them again.
VOLUME
1
2
3
4
5
6
7
8
0
100
9
CH
NAVI
SKIP
SLOW/SEARCH
MENU
ENTER
DIRECT
NAVIGATOR
TOP MENU
RETURN
OSD/
DISPLAY
TV
FM/AM
DVD/VHS
DVD
TV
VHS
TUNER
DISC 1
DISC 2
DISC 3
DISC 4
PICTURE MODE
SETUP
OPEN/CLOSE/EJECT
JET REW
CD MODE
DISC 5
S10
ENTER
PLAY
LIST
TV VOL
TV VOL
RESET
TV/VIDEO
PAGE
GROUP
MIX 2CH
SUBTITLE
REPEAT
PLAY MODE
MULTI RE-MASTER
SUBWOOFER LEVEL
C.S.M
SFC
C.FOCUS
SUPER SRND
PROGRESSIVE
MUTING
INPUT SELECTOR
OPEN/CLOSE
EJECT
DISC CHANGE
DISC CHECK
INPUT
SELECTOR
REC
/REW
FF/
STOP
PLAY
DOWN
UP
PHONES
CH
VOLUME
STOP
-DEMO
DISC
D I S C
1
2
3
4
5
1
2
3
4
5
PLAY
POWER
Í
/I
INPUT SELECTOR
ENTER
PLAY MODE
FM/AM
TUNER
Numbered
buttons
buttons
CH
CH
CH
Automatic presetting
Manual tuning
Presetting the channel one by one
PGM
Selecting the preset channels
ST
TUNED
MONO
7708en.book 44 ページ ２００４年２月１４日 土曜日 午後３時２４分