Panasonic wv-cm146 Manuale Utente
-14-
13
12
11
10
9
8
7
6
5
4
3
2
1
625
624
623
622
VITC
Real Time Recording
• Move the cursor to TIMING SELECT on SET UP MENU,
and select INT.
• Real time recording is performed with camera switch-
ing pulse supplied by WV-CM146.
• The pictures from each camera change frame by
frame.
• The recording speed of the time lapse VTR should be
set to 2 hours recording mode.
• You can record not only camera pictures but also the
audio in real time.
Note:
If no camera is connected to any channels, a
black picture may be mixed on the tape some-
times. This does not mean there is something
wrong with this monitor.
times. This does not mean there is something
wrong with this monitor.
1
1 field
1
2
2
1
1
3
3
1
1
4
4
1
1
2
2
■
Setting Up Time Lapse VTR
(AG-6730, AG-6740)
When using the AG-6730 or AG-6740 with WV-CM146, read
the operating instructions for AG-6730 or AG-6740 and
confirm the following points.
the operating instructions for AG-6730 or AG-6740 and
confirm the following points.
A. Menu Screen 3
1. Item-3 : Select LINE for the input video signal.
2. Item-5 : Set the time to 9:00 AM.
3. Item-6 : Assign VTR as either MASTER or SLAVE.
2. Item-5 : Set the time to 9:00 AM.
3. Item-6 : Assign VTR as either MASTER or SLAVE.
B. Menu Screen 4
1. Select HIGH alarm reset pulse acceptance level.
2. Item-6 : Set the camera switch timing to 1 FIELD.
3. Item-7 : Set TM2 camera switching mode.
2. Item-6 : Set the camera switch timing to 1 FIELD.
3. Item-7 : Set TM2 camera switching mode.
C. VITC signal (option)
Do not align this signal with ID-code of WV-CM146. The
VITC should be placed at 7H or 9H.
VITC should be placed at 7H or 9H.
• VITC Signal (7H and 9H)
2. Alarm Channel Spot Recording (SPOT)
Only the channel that receives the alarm signal is
recorded.
recorded.
The picture from the VTR are displayed on the monitor by
operating the MONITOR MODE switch and the INPUT
SELECT switch.
The following table shows the switching of picture and
audio with the MONITOR MODE switch and the INPUT
SELECT switch.
operating the MONITOR MODE switch and the INPUT
SELECT switch.
The following table shows the switching of picture and
audio with the MONITOR MODE switch and the INPUT
SELECT switch.
Alarm Recording Mode
When alarm signal is received, you can select one of the
following two recording modes;
following two recording modes;
1. Alarm Channel Priority Recording (FRAME)
The channel that received the alarm signal has priority
of recording.
The illustration below shows the REC OUT signal in
case 1 ch receives the alarm signal.
of recording.
The illustration below shows the REC OUT signal in
case 1 ch receives the alarm signal.
MONITOR
MODE
INPUT
SELECT
SELECT
QUAD/SPOT
SEQ/VTR
CAMERA
Picture to be dis-
played :
played :
QUAD
(1-4ch/5-8ch)
SPOT (1 - 8ch)
(1-4ch/5-8ch)
SPOT (1 - 8ch)
Audio output :
SEQUENCE
(1-4ch
(1-4ch
*1
)
SPOT (1 - 4 ch
*1
)
Picture to be dis-
played :
played :
SEQUENCE
(1 - 30sec.)
SPOT (1 - 8ch)
(1 - 30sec.)
SPOT (1 - 8ch)
Audio output :
SEQUENCE
(1 - 4ch)
SPOT (1 - 4 ch)
(1 - 4ch)
SPOT (1 - 4 ch)
VTR
Picture to be dis-
played :
played :
(VTR playback pic-
ture supplied from
PLAY IN connector.
ture supplied from
PLAY IN connector.
*2
)
QUAD
(1 - 4ch/5-8ch)
SPOT (1 - 8ch)
SPOT (1 - 8ch)
Audio output :
Output from AUDIO
IN connector
IN connector
Picture to be dis-
played :
played :
Direct video picture
supplied from PLAY
IN connector.
supplied from PLAY
IN connector.
Audio output :
Output from AUDIO
IN connector
IN connector
*1. When an alarm signal is supplied, the audio from the
channel that receives the alarm signal sounds.
*2. In QUAD/SPOT mode, only recorded tapes by WV-
CM146, and recorded tapes by WJ-FS20 with no VITC
signal can be reproduced.
signal can be reproduced.