Yamaha RX-V1000RDS Manuale Utente
REMOTE CONTROL FEATURES
58
■
Controlling a different
component from the source
component (input) you have
selected
component from the source
component (input) you have
selected
1
Repeat steps 1 and 2 of the procedure in
“Setting the Manufacturer Code”.
“Setting the Manufacturer Code”.
2
Press
l
/
h
to select a library (component
category).
There are 13 libraries to set up a manufacturer code:
L:TV, L:CAB (CABLE), L:DBS, L:SAT, L:VCR,
L:DVD, L:LD, L:CD, L:CDR, L:MD, L:TAP (TAPE),
L:TUN (TUNER) and *L:AMP.
L:TV, L:CAB (CABLE), L:DBS, L:SAT, L:VCR,
L:DVD, L:LD, L:CD, L:CDR, L:MD, L:TAP (TAPE),
L:TUN (TUNER) and *L:AMP.
3
Repeat steps 3 and 4 of the procedure in
“Setting the Manufacturer Code”.
“Setting the Manufacturer Code”.
About amplifier libraries (L:AMP)
L:AMP has 4 codes: YPC (factory setting), Zone2,
DSP, and No. “YPC” should be selected to operate this
unit. “Zone2” is for operating YAMAHA DSP
amplifiers with Zone 2 feature. “DSP” is for operating
YAMAHA DSP amplifiers other than this unit. “No” is
to clear this unit control area functions.
DSP, and No. “YPC” should be selected to operate this
unit. “Zone2” is for operating YAMAHA DSP
amplifiers with Zone 2 feature. “DSP” is for operating
YAMAHA DSP amplifiers other than this unit. “No” is
to clear this unit control area functions.
6CH INPUT
TITLE
ENTER
MENU
SOUND
DISPLAY
SOURCE
SELECT
SEARCH
CHAPTER
POWER
REC
STOP
PAUSE
PLAY
+
–
/
TRANSMIT
RE-NAME
CLEAR
MACRO
MACRO
LEARN
OFF
ON
SYSTEM
POWER
STANDBY
PHONO
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
6CH INPUT
TITLE
ENTER
SYSTEM
POWER
POWER
STANDBY
PHONO
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
10KEY DSP
Programming a New Remote
Control Function (Learn Feature)
Control Function (Learn Feature)
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
• This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
1
Set 10KEY/DSP to 10KEY.
2
Press an input selector button, A or B to
select a source component.
select a source component.
3
Place this remote control and the other
remote control about 50 to 100 mm (2 to
4 in.) apart on a flat surface so that their
infrared transmitters are aimed at each other.
remote control about 50 to 100 mm (2 to
4 in.) apart on a flat surface so that their
infrared transmitters are aimed at each other.
about 50 to 100 mm
(2 to 4 in.)
(2 to 4 in.)
0110V1000RDS_57-63_EN
9/5/0, 4:43 PM
58