Sanyo VDC-C1574VA Manuale Utente

J

You can use the monitor checking cable (sold separately) to 
display an image on a monitor when setting up the camera to check 
the surveillance angle and range, lens focus, etc.
Connect the connector of the monitor checking cable to the monitor 
checking connector (a) on the circuit board and connect the jack 
of the monitor checking cable to the monitor.

J

Once the camera has been installed, adjust the lens section.

 

Be careful not to touch the lens section when changing the angle 

of the camera.

 

When loosening the drop-prevention cord fixing screw, be 

careful not to loosen it too much; otherwise the dome cover may 
drop.

 

Loosen the screw (A) with a Phillips head screwdriver before 

adjusting the tilt position.

NOTE on image direction (Wall Installed):
If the monitor image is misaligned, follow the steps below to adjust.
c

Loosen the screws (B) with the supplied hexagon wrench 
(small).

d

Turn the indented dial (C) to adjust the image direction.

e

Tighten the screws (B) after adjustments are finished.

J

When connected to power, the VDC-D1584VA turns on the DAY/
NIGHT function for continuous operation.
The DAY/NIGHT function automatically switches over between 
color and black-and-white mode depending on the ambient 
brightness; for example, choosing color mode during daytime, and 
black-and-white mode for nighttime monitoring with its increased 
sensitivity in a darker environment.

This function is disabled if 4 is set to "Down".

J

The camera comes from the factory pre-adjusted and ready to 
install, but you can make adjustments or settings if you need.
If you have trouble adjusting the camera, consult your dealer or an 
Authorized Sanyo Service Center.
(=Factory default setting)

1

 

This function is disabled if 4 is set to "Down".

 

If backlight compensation is not corrected in the VDC-C1574VA and 
VDC-D1584VA when 1 is set to “ON”, you can correct by adjusting level 
volume 6.

60

60

1 2 3 4

6

6

7

7

2 3 5 4

J

Check for polarity when using a DC 12 V 
power supply (Polarity does not matter when 
using a AC 24 V power supply).

J

J

Black

Red

Supported coaxial cables 
You can use any of the following coaxial cables:
 

RG-59U (3C-2V) Length: 250 m (273.4 yds) max.

 

RG-6U (5C-2V)

Length: 500 m (546.8 yds) max.

 

RG-11U (7C-2V) Length: 600 m (656.2 yds) max.

 

When using an RG-59U (3C-2V) cable, do not attach it 
to piping or wiring.

 

Select the cable according to the distance between the 
devices you wish to connect.

 

If you use a cable other than the types above, the image 
or sync signal will be attenuated and will not be 
transmitted correctly.

Monitor checking 

connector (a)

Screw (A)

FOCUS

ZOOM

Screw (B)

Monitor checking 

connector (a)

Screw 
(B)

Indented

dial (C)

Drop-

prevention

cord fixing

screw

Compensates for backlighting with the 
centerweighted metering mode. 

Down 

This function is off.

2

NOTE:
This factory preset is optimal, so it is not necessary to change the 
setting.

3

VDC-C1574VA, VDC-D1584VA

VDC-W1594VA

4

For adjusting the sensitivity of the camera. Use this setting for 
shooting in dark environments.

5

Correction is made for simultaneous monitoring of subjects which 
are different in brightness, one in a dark room and another in bright 
outdoor environment, for example.

6

If the entire image is too dark or bright, or the backlight 
compensation is not correct even after 1 is set to “ON”, you need 
to adjust the level volume.

7

Vertical sync disturbance may occur when a selector is used to 
switch between multiple cameras connected to one monitor. To 
prevent vertical sync disturbance, adjust 7.

When using the DC 12V adaptor, sync setting is set to internal 
sync.

ON 

AI: Normal setting (Auto iris)

EI: Electronic iris

ATW-A (Auto-tracing white balance - All): Automatic 
setting for white balance, covering wider range of 
color temperature than with “ATW”.

• May result in an excessively and unnaturally 

effected image, depending on the conditions.

Down 

ATW (Auto-tracing white balance): Automatic setting 
for white balance.

ON 

ATW-A (Auto-tracing white balance - All): Automatic 
setting for white balance, covering wider range of 
color temperature than with “ATW”.

• May result in an excessively and unnaturally 

effected image, depending on the conditions.

ATW (Auto-tracing white balance): Automatic setting 
for white balance.

ON 

Normal setting

Set this when there is excessive noise (AGC off)

ON 

When monitoring of subjects which differ in 
brightness.

This function is off.

Opens the lens iris, making the entire 
image brighter

Closes the lens iris, making the entire 
image darker

Press the button to eliminate sync 
disturbances when needed.

Press each button to eliminate sync 
disturbances when needed.

In order to obtain warranty service, the product must be delivered to and picked up from an 
Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in 
this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained 
by calling the toll-free number listed below.

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN 
THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND 
PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL 
PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR 
RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE 
CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company 
warrants this SANYO product against defects in materials and workmanship for the periods 
specified below. SFC will repair or replace (at its option) the product and any of its parts which fail 
to conform to this warranty. The warranty period commences on the date the product was first 
purchased or rented at retail.

For product operation, authorized service center referral, service assistance or problem 
resolution, call

For accessories and/or parts, call

LABOR

PARTS

IMAGE DEVICE

3 YEARS

3 YEARS

3 YEARS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in 
the appropriate model's instruction manual, or (B) the repair of any product whose serial number 
has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or 
reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the 
control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting 
from unauthorized service or parts, improper maintenance, operation contrary to furnished 
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, 
neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and 
tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize 
any party to assume for it any other obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO 
THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN 
NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL 
DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY 
DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO 
CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND 
DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN 
CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING 
WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER 
SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE 
PURCHASE PRICE OF THE PRODUCT.

For your protection in the event of theft or loss of this product, please fill in the information below 
for your own personal records.

Model No.

Serial No.

(Located on back or bottom side of unit.)

Date of Purchase

Purchase Price

Where Purchased

L5BN2_US(VDC-C1574VA)(GB).fm  2 ページ  ２００６年１２月１日　金曜日　午前１２時１４分