EnGenius Technologies durafon 1x Manuale Utente

~27~

[Note] Intercom numbers (Handset ID) are not stored in the last 10 
numbers dialed log. 

1.  When an incoming call arrives, the ringer will ring or vibrate unless the 

ringer has been turned off. 

 

 

 

2.

If the handset is on the charger cradle (ringer will be temporarily 
switched to “Ring” if it has been set to “Vibrate”), lift the handset and 
start conversation. 

 

 

 

3.  If the handset is not on the cradle, press any key (except END, and the 

Silent soft key) to answer. 

1.  You can press 

SILENT

 (Left) soft key if you choose to ignore 

the call.  Unlike turning off the ringer (from the handset menu), 
the

SILENT

 key operation is valid only for the current call.  

2.  If Caller ID service is available, the LCD will display the 

incoming call information.  If the LCD shows “Private” or 
“Unknown”, the caller’s information may have been blocked by 
the caller or the originating phone company. 

1.  When an intercom call arrives, the ringer will ring or vibrate unless the 

ringer has been turned off. Press TALK to answer the intercom call. 

 

 

 

2.

If the handset is on the charger cradle (ringer will be temporarily 
switched to “Ring” if it has been set to “Vibrate”), lift the handset and 
start conversation. 

 

 

 

3.

If the handset is not on the cradle, press any key (except PWR, END, 
and the SILENT soft key) to answer. 

1.  The LCD displays the caller’s Handset ID. 
2.  You can press the 

SILENT

 if you choose to ignore the call.  Unlike 

turning off the ringer the SILENT key operation is valid only for the 
current call.

~28~

To end a telephone or intercom call, press END key or place handset into 
charger cradle. 

1.  Voice volume can only be adjusted during a call. 
 

 

 

2.  There are 6 levels of volume selections.  Default as 

volume 4. Use 

¿andÀ scrolling key to adjust. 

 

 

 

3.  The new setting remains effective for all future calls until changed. 

1.  When a call is in progress, it can be put on hold by 

pressing the 

HOLD

 (Right) soft key. 

 

 

 

2.

To return to the conversation, press “

UNHOLD

”

1.  The call being placed on hold can only be “un-hold” by the 

handset that puts it on hold. 

2.  Handset LCD displays a call is being on hold.  An alert tone 

(double beep) every 30 seconds will remind the handset that a 
call is being on hold. 

3.  If the operation (e.g., call transfer) after putting a call on-hold 

fails, the held call may be dropped. 

4.  You can power off the handset (e.g., change battery) while call 

is on hold.  After power on again, you can continue the call by 
pressing

UNHOLD

 (Left) soft key or select “3” from the Option 

menu to terminate the hold state. 

5.  You can only unhold the call with the base coverage.  Once 

you’re out of the base coverage, you can return to stand-by 
using “Clear hold” function in the OPTION list item #3.  

1.

After a link is established, you can press 

OPTION

 (Left) soft key and 

press “0” to mute the handset microphone. 

 

 

 

2.

When mute is active, the other end will not hear your voice, but still can 
speak to you. 

 

 

 

3.

To leave the mute state, press “

UNMUTE

” (Left) soft key. Mute is 

­ 11             

 00:00:10 
Volume:4 

OPTION          HOLD 

­ 11             

You have a 
Call on hold 

UNHOLD

OPTION