temco-tool 41dvn Manuale Utente

7

The height that a combustible mantel is fitted above the 
fireplace is dependent on the depth of the mantel. This 
also applies to the distance between the mantel leg (if 
fitted) and the fireplace.
For the correct mounting height and widths, refer to 
Figures 4a, 4b and the Mantel Chart below.
The distances and reference points are not affected by 
the fitting of a bay window front trim kit.
Noncombustible mantels and legs may be installed at 
any height and width around the appliance. When using 
paint or lacquer, it must be heat resistant to prevent 
discoloration. 

Top of unit to ceiling ................................. 36” (914 mm)
Front of unit to combustibles ................... 36” (914 mm)
Appliance
 

Top  ......................................................... 0” (0 mm)

 

Bottom ..................................................... 0” (0 mm)

 

Side ......................................................... 0” (0 mm)

 

Back ........................................................ 0” (0 mm)

Venting
Concentric sections of DV Vent ................... 1” (25 mm)
Nonconcentric sections of DV Vent 
 

Sides and bottom .................................. 1” (25 mm)

 

Top ........................................................ 2” (51 mm)

Flex Vent .................................................. 7/8” (22 mm)

J

F

G

H

I

Mantel

Leg

CFM164a

Mantel Leg Chart

06/22/01   sta

Black 

Surround 

Face

CFM164a

CFM170

DV Builder Front 

View

O

N

M

L

K

Side of 

Combustion Chamber

CFM170

Fig. 4b   Combustible mantel leg minimum installation.

 

 

 

F 

10” (254 mm) 

K 

11¹⁄₂” (292 mm)

 

G 

8” (203 mm) 

L 

9¹⁄₂” (241 mm)

 

H 

6” (152 mm) 

M 

7¹⁄₂” (191 mm)

 

I 

4” (101 mm) 

N 

5¹⁄₂” (140 mm)

 

J 

2” (51 mm) 

O 

3¹⁄₂’” (89 mm)

Y

E

A

B

C

D

F

Y

B

X

LU584-1

Locating unit

2/4/99   djt

A) Flat on wall  

B) Cross corner 

C)  **Island

D) Room divider 

E) Flat on wall corner 

F)  Chase installation

Y) Refer to “Clearance to Combustibles” Section

Note (Fig. 3):  
** Island (C) and Room Divider (D) installation is possible as 
long as the horizontal portion of the vent system (X) does not 
exceed 20’ (610 cm).  See details in Venting Section.

Fig. 3  Locating Gas Fireplace

LU584-1

A B C D E

V

W

X

Y

Z

CFM146

DV Mantel Chart

7/5/01   sta

Louvre Assembly 

Top

Top of Combustion 

Chamber

Bottom of Door Trim

CFM146

Fig. 4a  Combustible mantel minimum installation.

 

 

 

V 

10” (254 mm) 

A 

19” (483 mm)

 

W 

8” (203 mm) 

B 

17” (432 mm)

 

X 

6” (152 mm) 

C 

15” (381 mm)

 

Y 

4” (101 mm) 

D 

13” (330 mm)

 

Z 

2” (51 mm) 

E 

11” (279 mm)

Maintain Minimum 

3/4” (19 mm) 

Clearance to 

Combustibles