ATTO Technology 2400c-r-d Manuale Utente
7
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.3 ATTO FibreBridge 2390C
The ATTO FibreBridge 2390C is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI storage devices.
The FibreBridge 23900C is available in an industry-
standard 4U cPCI card. Default values are appropriate
for most applications. Refer to
Fibre Channel connectivity to Ultra320 SCSI storage devices.
The FibreBridge 23900C is available in an industry-
standard 4U cPCI card. Default values are appropriate
for most applications. Refer to
on page 15 for more information.
Board dimensions
Width:
6.1939 inches
Length:
6.299 inches
Height of tallest component:
.545 inches
Cooling and airflow
Operating temperature: 0-40 °C
Humidity: 10-90% non-condensing
Humidity: 10-90% non-condensing
Power
The FibreBridge
board may be
powered from the
cPCI backplane
connector or a 6-pin connector.
board may be
powered from the
cPCI backplane
connector or a 6-pin connector.
Input voltage:
5.0V
Power draw:
30 Watts
Battery-backed event log SRAM & Real-Time-
Clock:
Clock:
A rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small Formfactor
Pluggable (SFP) interface.
Pluggable (SFP) interface.
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connectors, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connectors, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from the
RJ-45 connector to support local and remote
diagnostics, monitoring and management.
A serial 10-pin
header provides
support for an RS-
232 remote
monitoring and
management port
through a Command
Line Interface. The baud rate is programmable and
preset at the factory to 115200 bps.
RJ-45 connector to support local and remote
diagnostics, monitoring and management.
A serial 10-pin
header provides
support for an RS-
232 remote
monitoring and
management port
through a Command
Line Interface. The baud rate is programmable and
preset at the factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green Ready LED
blinks.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green Ready LED
blinks.
LED indicators
The on-board LED indicators show through the
faceplate and follow left to right.
faceplate and follow left to right.
SCSI ports:
a green LED indicates activity if it is lit,
no activity if it is off.
Fibre Channel port:
A lighted green LED indicates
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
indicates activity if it is lit, no activity if it is off.
4
5
2
1
3
6
NU 5V GND 5V 5V GND
6-pin connection pinouts