Xyron 2500 Manuale Utente
When properly used, the Xyron 2500 is relatively maintenance-free. Listed below
are safeguards and tips that will produce better results. Refer to the exploded view
diagram for part descriptions.
are safeguards and tips that will produce better results. Refer to the exploded view
diagram for part descriptions.
Importance of a clean document:
For best results when laminating, it is highly recommended that the document be
cleaned with a soft, lint-free cloth immediately prior to lamination. Small dust or lint
particles may cause the laminate to “tent”, producing an appearance similar to a
small air bubble.
cleaned with a soft, lint-free cloth immediately prior to lamination. Small dust or lint
particles may cause the laminate to “tent”, producing an appearance similar to a
small air bubble.
Cut blade replacement and cleaning:
The cut blade may accumulate adhesive over time. Cleaning the blade must be
done with great care to avoid personal injury. To remove the blade, slide the orange
blade holder into the notch and lift upwards. Carefully remove the blade holder and
replace or clean with a light solvent such as isopropyl alcohol.
done with great care to avoid personal injury. To remove the blade, slide the orange
blade holder into the notch and lift upwards. Carefully remove the blade holder and
replace or clean with a light solvent such as isopropyl alcohol.
Use after storage:
For applications where the appearance of your laminated document is critical, it is
highly recommended that the Xyron 2500 be used and stored in a clean, dust-free
environment. Airborne dust particles and lint will tend to adhere to the bare adhesive
inside the supply roll. If the machine has not been used for several days or was
subject to a dusty environment, it is recommended that four inches (10cm) of material
be advanced and discarded before inserting your document. It is also recommended
that the feed tray is cleaned with a lint-free cloth. Contact your dealer about a dust
cover as an accessory.
highly recommended that the Xyron 2500 be used and stored in a clean, dust-free
environment. Airborne dust particles and lint will tend to adhere to the bare adhesive
inside the supply roll. If the machine has not been used for several days or was
subject to a dusty environment, it is recommended that four inches (10cm) of material
be advanced and discarded before inserting your document. It is also recommended
that the feed tray is cleaned with a lint-free cloth. Contact your dealer about a dust
cover as an accessory.
Cleaning adhesive from the nip rollers:
The nip rollers are designed to be self-cleaning under normal use. If adhesive does
accumulate, it can normally be removed by first removing the supply films from
between the nip rollers and advancing a scrap piece of regular bond paper through
the machine. The bare adhesive will tend to attach to the paper. If this method of
cleaning does not work, the nip rollers can be cleaned with a light solvent such as
isopropyl alcohol. Take care not to scratch, cut or chip the rollers. For best results
when laminating, it is critical that the lower idler bar be kept clean of adhesive build-up.
accumulate, it can normally be removed by first removing the supply films from
between the nip rollers and advancing a scrap piece of regular bond paper through
the machine. The bare adhesive will tend to attach to the paper. If this method of
cleaning does not work, the nip rollers can be cleaned with a light solvent such as
isopropyl alcohol. Take care not to scratch, cut or chip the rollers. For best results
when laminating, it is critical that the lower idler bar be kept clean of adhesive build-up.
Maintenance, Safeguards & Tips
If You Have Additional Questions, Contact the Xyron Technical Hotline:
800-793-3523 in the U.S.A. and +45-7594-5866 in Europe
E-mail address in the U.S.A.: comments@xyron.com
E-mail address in Europe: europe@xyron.dk
Also, check out our website at www.xyron.com
800-793-3523 in the U.S.A. and +45-7594-5866 in Europe
E-mail address in the U.S.A.: comments@xyron.com
E-mail address in Europe: europe@xyron.dk
Also, check out our website at www.xyron.com
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500