Casio sgw400h-1bv wrist watch sgw400h1bv Manuale Utente

Operation Guide 5176

•

 The illustration below shows which buttons you need to press to navigate between 

modes.

•

 In any mode (except when a setting screen, with fl ashing digits is on the display), 

press

B to illuminate the display.

General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.

•

 The watch returns to the Timekeeping Mode automatically if you do not perform any 

button operation for two or three minutes in the Alarm Mode.

•

 The watch will return to the Timekeeping Mode automatically if you do not perform 

any operation for about one hour after entering the Barometer/Thermometer Mode.

•

If you leave a setting screen with fl ashing digits on the display for two or three minutes 
without performing any operation, the watch exits the setting screen automatically.

Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing 
when you last exited the mode appears fi rst.

Scrolling
The

B and D buttons are used on the setting screen to scroll through data on the 

display. In most cases, holding down these buttons during a scroll operation scrolls 
through the data at high speed.

Use the Timekeeping Mode to set and view the current 
time and date.

•

 In the Timekeeping Mode, the graphic in the center of 

the display indicates the passage of seconds.

There are two Home City settings: actually selecting the Home City and selecting 
either standard time or daylight saving time (DST).

To confi gure Home City settings
1. In the Timekeeping Mode, hold down 

A until the 

currently selected city code (Home City) starts to fl ash. 
This is the city code setting screen.

•

 Before the city code starts to fl ash, the message 

SET Hold will appear on the display. Keep 

A

depressed until SET Hold disappears and the city 
code starts to fl ash.

•

 The watch will exit the setting mode automatically if 

you do not perform any operation for about two or 
three minutes.

•

 For details about city codes, see the “City Code Table” 

at the back of this manual.

2. Press 

D (East) and B (West) to select the city code 

you want to use as your Home City.

•

 Keep pressing 

D or B until the city code you want to 

select as your Home City appears on the display.

3. Press 

C to display the DST setting screen.

4. Press

D to toggle between Daylight Saving Time (On)

and Standard Time (OFF).

•

 Note that you cannot switch between standard time 

and daylight saving time (DST) while UTC is 
selected as your Home City.

5. After all the settings are the way you want, press 

A to return to the Timekeeping Mode.

•

 The DST indicator appears to indicate that Daylight Saving Time is turned on.

•

 After you specify a city code, the watch will use UTC* offsets in the World Time 

Mode to calculate the current time for other time zones based on the current 
time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. 

1. In the Timekeeping Mode, hold down 

A until the 

currently selected city code (Home City) starts to fl ash. 
This is the city code setting screen.

•

 Before the city code starts to fl ash, the message 

SET Hold will appear on the display. Keep 

A

depressed until SET Hold disappears and the city 
code starts to fl ash.

2. Press 

C to display the DST setting screen.

3. Press 

D to toggle between Daylight Saving Time (On)

and Standard Time (OFF).

4. After all the settings are the way you want, press 

A to 

return to the Timekeeping Mode.

•

 The DST indicator appears to indicate that Daylight 

Saving Time is turned on.

You can use the procedure below to adjust the current time and date settings if they 
are off.
Changing the digital Home City data should cause the analog time setting to change 
accordingly. If the analog time does not indicate the digital time, check the home 
positions of the hands and make adjustments if necessary (page E-22).

1. In the Timekeeping Mode, hold down 

A until the 

currently selected city code (Home City) starts to fl ash. 
This is the city code setting screen.

•

 Before the city code starts to fl ash, the message 

SET Hold will appear on the display. Keep 

A

depressed until SET Hold disappears and the city 
code starts to fl ash.

2. Use 

D and B to select the city code you want.

•

 Select your Home City code before changing any 

other setting.

•

 For full information on city codes, see the “City Code 

Table” at the back of this manual.

3. Press

C to move the fl ashing in the sequence shown below to select the other settings.

Barometer
unit

Temperature
unit

Illumination
Duration

Button Operation 
Tone On/Off

Day

City
Code

DST

Altitude
unit

12/24-Hour
Format

Seconds

Hour

Minute

Year

Month

•

 The following steps explain how to confi gure timekeeping settings only.

4. When the timekeeping setting you want to change is fl ashing, use 

B and/or D to 

change it as described below.

Change the city code

Use

D (East) and 

B (West).

Toggle between Daylight Saving Time (On)
and Standard Time (OFF).

Press

D.