Chauvet LEGEND 1200E Manuale Utente
Setup
Legend™ 1200E Spot User Manual Rev. 03c
-7-
3. Setup
AC Power
The Legend™ 1200E Spot has an auto-ranging power supply that can work with an
input voltage range of 200~240 VAC, 50/60 Hz.
input voltage range of 200~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this guide, the product’s user manual, or on the product’s sticker.
specifications in this guide, the product’s user manual, or on the product’s sticker.
Always connect the Legend™ 1200E Spot to a protected circuit with an
appropriate electrical ground to avoid the risk of electrocution or fire.
appropriate electrical ground to avoid the risk of electrocution or fire.
To determine the power requirements for the Legend™ 1200E Spot see the label affixed
to the bottom of the fixture. Alternatively, you may refer to the corresponding
specifications chart in the Technical Information chapter of this manual.
to the bottom of the fixture. Alternatively, you may refer to the corresponding
specifications chart in the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download the “Sizing the Circuit Breakers” document
from the CHAUVET® Web site.
For more information, you may download the “Sizing the Circuit Breakers” document
from the CHAUVET® Web site.
Never connect the Legend™ 1200E Spot to a rheostat (variable resistor) or
dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100%
switch.
dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100%
switch.
AC Plug
The Legend™ 1200E Spot has a bare-ended power input cord that is hard-wired to the
base of the fixture. Use the table below to wire a plug for the power cord.
base of the fixture. Use the table below to wire a plug for the power cord.
Connection
Wire (US)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Make sure to disconnect the fixture’s power cord before replacing a blown fuse,
and always replace it with a fuse of the same type and rating.
and always replace it with a fuse of the same type and rating.
Fuse Replacement
1) With a Phillips #2 screwdriver, unscrew the fuse holder from its housing.
2) Remove the blown fuse from its holder and replace it with a good fuse of the exact
same type and rating.
3) Screw the fuse holder back in its place and reconnect power.
DMX Linking
You may link any Legend™ 1200E Spot fixture to a DMX controller using a standard
DMX serial connection. If using other DMX compatible fixtures with a Legend™ 1200E
Spot, it is possible to control them individually with a single DMX controller.
DMX serial connection. If using other DMX compatible fixtures with a Legend™ 1200E
Spot, it is possible to control them individually with a single DMX controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the Legend™ 1200E Spot fixture to a DMX controller, you may
download the “DMX Primer” document from the CHAUVET® Web site.
cables needed to link the Legend™ 1200E Spot fixture to a DMX controller, you may
download the “DMX Primer” document from the CHAUVET® Web site.
DMX Modes
The Legend™ 1200E Spot can operate in 23 and 31-channel DMX modes. You will find
information about these DMX modes in the Introduction chapter (brief description), the
Operation Instructions chapter (configuration details), and the DMX Values section
(individual channel values).
information about these DMX modes in the Introduction chapter (brief description), the
Operation Instructions chapter (configuration details), and the DMX Values section
(individual channel values).