Husqvarna soff-cut 150 Manuale Utente
6
EXCEL SERIES BLADES
The Excel Series of diamond blades have been designed specifically for the Soff-Cut Ultra Early Entry dry cutting system of
green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates.
green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates.
Choose the correct specification of diamond blade for your area as follows:
Purple Excel Series 1000
XL6-1000
Ultra hard aggregate and non abrasive sand
Green Excel Series 2000
XL6-2000
Hard to ultra hard aggregate and non abrasive sand
Red Excel Series 3000
XL6-3000
Hard aggregate, medium abrasive sand
Orange Excel Series 4000
XL6-4000
Medium hard aggregate, medium abrasive sand
Yellow Excel Series 5000
XL6-5000
Medium hard to soft aggregate, abrasive sand
Black Excel Series 6000
XL6-6000
Soft aggregate, highly abrasive sand
Step 1
With the saw turned off, fold the saw handle to its full upright
position and install the locking pin in the handle. With both
hands, push down on the handlebar and raise the saw to its
full height and locked position.
Step 2
Remove the blade block cover (A) by turning the two locking
knobs counter-clockwise. With the two wrenches supplied with
the saw, insert one in the slot at the front of the engine and
one on the bolt on the blade shaft in the blade block (J). Rotate
the blade shaft counter-clockwise with wrench on the blade
With the saw turned off, fold the saw handle to its full upright
position and install the locking pin in the handle. With both
hands, push down on the handlebar and raise the saw to its
full height and locked position.
Step 2
Remove the blade block cover (A) by turning the two locking
knobs counter-clockwise. With the two wrenches supplied with
the saw, insert one in the slot at the front of the engine and
one on the bolt on the blade shaft in the blade block (J). Rotate
the blade shaft counter-clockwise with wrench on the blade
shaft bolt (C) until the second wrench engages the flats on the
other end of the shaft.
other end of the shaft.
Step 3
Remove the blade shaft bolt by continuing to turn the bolt
Remove the blade shaft bolt by continuing to turn the bolt
counter-clockwise. Remove the outer arbor washer or flange
(D).
(D).
WARNING
Inspect the blade (F) for any damage. Do not use any
blade that has cracks, nicks, flaws or a damaged arbor.
Make sure the blade is marked with a maximum operat-
ing speed greater than 4450 rpm.
Make sure the blade is marked with a maximum operat-
ing speed greater than 4450 rpm.
Step 4
Match the blade tri-arbor to the blade shaft arbor and install
Match the blade tri-arbor to the blade shaft arbor and install
the blade firmly against the rear flange (H). Insure the blade is
installed on the tri-arbor correctly. Match the female tri-arbor of
installed on the tri-arbor correctly. Match the female tri-arbor of
the outer washer or flange with the blade shaft and install the
blade shaft bolt turning clockwise. Be sure the outer flange is
fully seated and firmly holding the diamond blade in position.
Step 5
Install a new skid plate (G) by hooking the front on the front
blade block shaft pin. Connect the rear blade block shaft and
the rear of the skid plate by installing the locking pin (B).
Install a new skid plate (G) by hooking the front on the front
blade block shaft pin. Connect the rear blade block shaft and
the rear of the skid plate by installing the locking pin (B).
Step 6
Install the blade cover by turning the two knobs and tighten un-
til fully seated against the blade block. Lift the front and rear of
the skid plate to insure the blade slides through the skid plate
freely.
Install the blade cover by turning the two knobs and tighten un-
til fully seated against the blade block. Lift the front and rear of
the skid plate to insure the blade slides through the skid plate
freely.
Step 7
Insure the lexan shields (E & K) move freely up and down.
When replacing a worn blade, thoroughly clean the concrete
from blade block and blade cover before installing the new
blade. Discard the old skid plate and replace it with a new skid
plate.
When replacing a worn blade, thoroughly clean the concrete
from blade block and blade cover before installing the new
blade. Discard the old skid plate and replace it with a new skid
plate.
NOTE:
The patented skid plate is the most important part of the
Soff-Cut Ultra Early Entry system. If it is bent, twisted or
damaged, spalling and raveling of a cut may result. Store
skid plates carefully and install them properly. Install a
new skid plate with each new blade. Never re-use skid
plates.
The patented skid plate is the most important part of the
Soff-Cut Ultra Early Entry system. If it is bent, twisted or
damaged, spalling and raveling of a cut may result. Store
skid plates carefully and install them properly. Install a
new skid plate with each new blade. Never re-use skid
plates.
A
C
D
F
E
B
H
G
J
L
K
BLADE AND SKID PLATE INSTALLATION