ICOM ic-f3062t-s Manuale Utente
9
2
PANEL DESCRIPTION
2
DTMF AUTODIAL KEY “
D
DT
TM
MA
A
”
➥
Push to enter the DTMF channel selection mode. Then
select the desired DTMF channel using [CH Up]/[CH
Down].
select the desired DTMF channel using [CH Up]/[CH
Down].
➥
After selecting the desired DTMF channel, push this key to
transmit the DTMF code.
transmit the DTMF code.
RE-DIAL KEY “
D
DT
TM
MR
R
”
Push to transmit the last-transmitted DTMF code.
CALL KEYS “
C
CA
AL
LL
L
” “
C
CA
AL
LA
A
” “
C
CA
AL
LB
B
”
Push to transmit a 2/5-tone/BIIS ID code.
• Call transmission is necessary before you call another station
depending on your signaling system.
• [Call A] and/or [Call B] may be available when your system employs
selective ‘Individual/Group’ calls. Ask your dealer which call is
assigned to each key.
assigned to each key.
EMERGENCY KEY “
E
EM
MR
R
”
➥
Push and hold for a specified period to transmit an emer-
gency call.
gency call.
➥
When [Emergency Single (Silent)] or [Emergency Repeat
(Silent)] is pushed, an emergency call is transmitted without
a beep emission and LCD indication change.*
(Silent)] is pushed, an emergency call is transmitted without
a beep emission and LCD indication change.*
• If you want to cancel the emergency call, push (or push and
hold) the key again before transmitting the call.
• The emergency call is transmitted one time only or repeatedly
until receiving a control code depending on the pre-setting.
*BIIS PMR operation only
SURVEILLANCE KEY “
S
SU
UR
RV
V
”
Push to turn the surveillance function ON or OFF.
When this function is turned ON, the beep is not emitted and
the LCD backlight does not light when a signal is received or
a key is pushed, etc.
When this function is turned ON, the beep is not emitted and
the LCD backlight does not light when a signal is received or
a key is pushed, etc.
TX CODE ENTER KEY “
T
TX
XC
CE
E
”
(PMR or BIIS PMR operation only)
Push to enter the ID code edit mode directly, for both 5-tone
and BIIS. Then set the desired digit using [CH Up]/
[CH Down] or 10-keypad*. ((
Push to enter the ID code edit mode directly, for both 5-tone
and BIIS. Then set the desired digit using [CH Up]/
[CH Down] or 10-keypad*. ((
☞
p. 14))
*IC-F3062T/IC-F4062T (10-key type) only
TX CODE CHANNEL SELECT KEY “
T
TX
XC
C
”
➥
Push to enter the ID code channel selection mode directly.
Then set the desired channel using [CH Up]/[CH Down].
((
Then set the desired channel using [CH Up]/[CH Down].
((
☞
p. 14))
➥
During ID code channel selection mode, push for 1 sec. to
enter the ID code edit mode for 5-tone and BIIS. Then set
the desired digit using [CH Up]/[CH Down] or 10-keypad*.
((
enter the ID code edit mode for 5-tone and BIIS. Then set
the desired digit using [CH Up]/[CH Down] or 10-keypad*.
((
☞
p. 14))
*IC-F3062T/IC-F4062T (10-key type) only
TX CODE CHANNEL UP/DOWN KEYS “
T
TX
XC
CU
U
” “
T
TX
XC
CD
D
”
Push to select a TX code channel directly.