Garmin gpsmap 172 Manuale Utente
82
Appendix C
Messages
Proximity Alarm List is Full— You have used all ten proximity
waypoints.
Proximity Alarm Waypoint— You have entered the alarm radius for the
proximity waypoint indicated.
Proximity Overlaps Another Proximity Waypoint—The alarm radius
specified overlaps the area specified for another proximity waypoint. Adjust
the distance.
Route Already Exists: <route name>— You have entered a route name
that already exists in memory. Modify the route name or delete the previous
route name.
Route Does Not Exist: <route name>— Route has been renamed or
removed from memory and cannot be used.
Route Is Full— You have attempted to add more than 50 points to a route.
Reduce the number of points or create a second route.
Route Memory Is Full Can’t Create Route— Maximum amount of 50
routes is already in the unit’s memory and no additional routes can be
added until existing ones are removed.
Route Truncated— An uploaded route from another device has more than
50 points. Reduce the number of points.
Running Simulator— The unit is in simulator (practice) mode.
waypoints.
Proximity Alarm Waypoint— You have entered the alarm radius for the
proximity waypoint indicated.
Proximity Overlaps Another Proximity Waypoint—The alarm radius
specified overlaps the area specified for another proximity waypoint. Adjust
the distance.
Route Already Exists: <route name>— You have entered a route name
that already exists in memory. Modify the route name or delete the previous
route name.
Route Does Not Exist: <route name>— Route has been renamed or
removed from memory and cannot be used.
Route Is Full— You have attempted to add more than 50 points to a route.
Reduce the number of points or create a second route.
Route Memory Is Full Can’t Create Route— Maximum amount of 50
routes is already in the unit’s memory and no additional routes can be
added until existing ones are removed.
Route Truncated— An uploaded route from another device has more than
50 points. Reduce the number of points.
Running Simulator— The unit is in simulator (practice) mode.
Shallow Water Alarm— Specified shallow water alarm depth has been
detected below transducer.
Sonar Failed Unit Needs Repair— Internal problem with the unit.
Contact your dealer or Garmin Customer Service (page. iv) to have the unit
serviced.
Track Already Exists: <track name>— You have entered a saved track
name that already exists in memory. Modify the track name or delete the
previous track name.
Track Memory Is Full Can’t Create Track— Track log memory is full.
No additional track log data can be stored without deleting old data to
create memory space.
Track Truncated— A complete uploaded track does not fit into memory.
The oldest track log points were deleted to make space for the most recent
data.
Transducer Disconnected Sonar Turned Off— No transducer attached
or bad cable/transducer.
Transfer Complete— The unit has finished uploading/downloading infor-
mation to the connected device.
Water Speed Sensor is Not Working— Speed sensor is not detected.
Check connections.
Waypoint Already Exists: <waypoint name>— You have entered a
waypoint name that already exists in memory. Modify the waypoint name or
delete the previous waypoint name.
Waypoint Memory Is Full Can’t Create Waypoint— You have used all
3000 waypoints available. Delete unwanted waypoints to make space for
new entries.
detected below transducer.
Sonar Failed Unit Needs Repair— Internal problem with the unit.
Contact your dealer or Garmin Customer Service (page. iv) to have the unit
serviced.
Track Already Exists: <track name>— You have entered a saved track
name that already exists in memory. Modify the track name or delete the
previous track name.
Track Memory Is Full Can’t Create Track— Track log memory is full.
No additional track log data can be stored without deleting old data to
create memory space.
Track Truncated— A complete uploaded track does not fit into memory.
The oldest track log points were deleted to make space for the most recent
data.
Transducer Disconnected Sonar Turned Off— No transducer attached
or bad cable/transducer.
Transfer Complete— The unit has finished uploading/downloading infor-
mation to the connected device.
Water Speed Sensor is Not Working— Speed sensor is not detected.
Check connections.
Waypoint Already Exists: <waypoint name>— You have entered a
waypoint name that already exists in memory. Modify the waypoint name or
delete the previous waypoint name.
Waypoint Memory Is Full Can’t Create Waypoint— You have used all
3000 waypoints available. Delete unwanted waypoints to make space for
new entries.