Roland VC-2 Manuale Utente
39
Settings Common to All Modes (System Mode)
Audio I/F
Tx
Breath
STORE
—
Store the chord you specified from the
keyboard into the chord set.
keyboard into the chord set.
Parameter
Value
Explanation
MIC Jack
Switch
Switch
OFF, ON
Specifies whether the front pan-
el MIC jack will be enabled
(ON) or disabled (OFF).
el MIC jack will be enabled
(ON) or disabled (OFF).
INPUT Jack
Switch
Switch
OFF, ON
Specifies whether the rear panel
INPUT jacks will be enabled
(ON) or disabled (OFF).
INPUT jacks will be enabled
(ON) or disabled (OFF).
INPUT Jack
Gain
Gain
0db, +12db
Sets the gain of the rear panel
INPUT jacks.
INPUT jacks.
USB Audio In-
put Source
put Source
OFF, MAIN,
ANALOG
ANALOG
When the V-Synth XT is con-
nected via USB to your comput-
er, this specifies the source of
the USB audio that will be out-
put to the computer.
nected via USB to your comput-
er, this specifies the source of
the USB audio that will be out-
put to the computer.
USB Audio In-
put Monitor
Sw
put Monitor
Sw
OFF, ON
Specifies whether USB Audio
Input Source monitoring will be
sent from the V-Synth XT’s
MAIN OUT (ON) or will not be
sent (OFF).
Input Source monitoring will be
sent from the V-Synth XT’s
MAIN OUT (ON) or will not be
sent (OFF).
USB Audio
Output Dest
Output Dest
OFF, MAIN,
DIR
DIR
When the V-Synth XT is con-
nected via USB to your comput-
er, this specifies the output
destination of the USB audio
that is received from the com-
puter.
nected via USB to your comput-
er, this specifies the output
destination of the USB audio
that is received from the com-
puter.
Parameter
Value
Explanation
Front Panel
Sound
Generator
MIC Jack
INPUT
Jack
R
L
INPUT
JACK
Gain
INPUT
JACK
Switch
MIC
JACK
Switch
MIC Sw
•Hi-Z
•NORMAL
•PHANTOM
•NORMAL
•PHANTOM
Input Knob
PEAK LED
Rear Panel
Carrier
(Processor
Type 1, 2)
(Processor
Type 1, 2)
Modulator (MIC)
Controller Settings (Controller)
Parameter
Value
Explanation
Patch Tx
Ch
Ch
1–16,
RX CH,
OFF
RX CH,
OFF
Specifies the transmit channel of MIDI
messages in Patch mode. If you do not
want to transmit MIDI messages to ex-
ternal MIDI devices, turn this parameter
“OFF.” If you want the transmit channel
to always match the Patch Receive
Channel, set this parameter to “RX CH.”
messages in Patch mode. If you do not
want to transmit MIDI messages to ex-
ternal MIDI devices, turn this parameter
“OFF.” If you want the transmit channel
to always match the Patch Receive
Channel, set this parameter to “RX CH.”
Tx PC
OFF,
ON
ON
Specifies whether Program Change mes-
sages will be transmitted (ON) or not
(OFF).
sages will be transmitted (ON) or not
(OFF).
Tx Bank
OFF,
ON
ON
Specifies whether Bank Select messages
will be transmitted (ON) or not (OFF).
will be transmitted (ON) or not (OFF).
Tx Active
Sens
Sens
OFF,
ON
ON
Specifies whether Active Sensing mes-
sages will be transmitted (ON) or not
(OFF).
sages will be transmitted (ON) or not
(OFF).
Parameter
Value
Explanation
Voice As-
sign
sign
OFF,
CC01–31,
CC33–95
CC01–31,
CC33–95
Specifies the MIDI controller
number that will transmit the
volume data extracted from the
mic input signal.
number that will transmit the
volume data extracted from the
mic input signal.
OFF
: No message will be trans-
mitted.
CC01-31, 33-95
: Controller
numbers 1-31, 33-95
Parameter
Value
Explanation
INPUT
Jack
MIC
Jack
DIRECT
OUT
OFF
ANALOG
MAIN
DIR
MAIN
V-Synth XT
USB Audio OUT
USB Audio IN
USB A
udio Output Dest
USB A
udio Input Source
MAIN
OUT
INPUT
Monitor
Switch
Sound Generator
vc2_for_XT_e1 39 ページ ２００５年３月８日 火曜日 午後４時５２分