Ultra Start 600 Manuale Utente
Installation Guide
Recommended Pre-Installation Procedures
Recommended Installation Procedures
Mounting the Module
Installing The Led
Installing The Program Button
Connecting The Starter Disable
Connecting The Dome Light Supervision
Under Hood Connections
Mounting The Siren
BEFORE STARTING INSTALLATION:
- Discuss the optional features with the customer.
- Discuss the optional features with the customer.
- Do a walk around the vehicle and check for any damage.
- If installing a LED discuss the placement with customer before installing.
- If installing a LED discuss the placement with customer before installing.
- Take a few minutes to review the installation and owners manuals.
INSTALLATION TIPS
4
Route the hood pin (optional) and Siren wire through the firewall, into the engine compartment. Always
try to pull the wires through a factory rubber grommet. If drilling through the firewall, BE CAREFUL.
Check for obstructions on both sides of the firewall. After drilling use a snap in grommet to protect the
wires from sharp edges.
try to pull the wires through a factory rubber grommet. If drilling through the firewall, BE CAREFUL.
Check for obstructions on both sides of the firewall. After drilling use a snap in grommet to protect the
wires from sharp edges.
Never mount the module in the engine compartment. Select a location under the dash to install the main
module. Be certain that the module is securely attached and does not obstruct any serviceable areas.
Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a
thief. The module must be free from all moving parts such as brake, clutch and gas pedals and the
linkages that are attached to them.
module. Be certain that the module is securely attached and does not obstruct any serviceable areas.
Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a
thief. The module must be free from all moving parts such as brake, clutch and gas pedals and the
linkages that are attached to them.
Choose a location in the engine compartment that is away from high heat sources and direct exposer to
water. The siren should be mounted as well as grounded to solid metal. Run the wiring for the siren so
that it can not be seen or reached from below the vehicle.
water. The siren should be mounted as well as grounded to solid metal. Run the wiring for the siren so
that it can not be seen or reached from below the vehicle.
Choose a location that will be highly visible when the LED is installed.Most vehicles are equipped with
knock out panels in the dashboard, these panels are easily removable and can be easily replaced if
necessary. Once the location is picked, use a 5/16th drill bit and drill a hole through the panel. Test fit the
LED into the hole. If the hole was drilled to large, place the LED in the hole and glue in place from the
back of the panel. Plug the Led into the Red connector on the main module.
knock out panels in the dashboard, these panels are easily removable and can be easily replaced if
necessary. Once the location is picked, use a 5/16th drill bit and drill a hole through the panel. Test fit the
LED into the hole. If the hole was drilled to large, place the LED in the hole and glue in place from the
back of the panel. Plug the Led into the Red connector on the main module.
Choose a location to mount the Program Button. This location should be hidden and not visible from
outside the vehicle. Once the location of the switch is picked, use a 1/4” drill bit and drill a hole. Remove
the nut and push the Program button through the hole. Replace the nut and tighten until the switch is
secure. Plug the valet into the Blue connector of the main module.
outside the vehicle. Once the location of the switch is picked, use a 1/4” drill bit and drill a hole. Remove
the nut and push the Program button through the hole. Replace the nut and tighten until the switch is
secure. Plug the valet into the Blue connector of the main module.
Take the brown starter kill wire from the box and cut in half, then locate the vehicles starter wire. This
wire will switch to 12volts in the crank or start position only. Cut this wire in half and confirm that the
vehicle will not start. Connect the brown wires, one to each side of the cut starter wire. Route the brown
wires to the main module and connect to the starter kill plug.
wire will switch to 12volts in the crank or start position only. Cut this wire in half and confirm that the
vehicle will not start. Connect the brown wires, one to each side of the cut starter wire. Route the brown
wires to the main module and connect to the starter kill plug.
Determine the door pin type. Positive, door pin wire switches to 12 volts when the door is opened.
Negative, door pin wire switches to ground when the door is opened. For positive door, connect one of the
black/white wires to 12volts and the other to the door pin wire. For negative connect one of the
black/white wires to ground and the other to the door pin wire.
Negative, door pin wire switches to ground when the door is opened. For positive door, connect one of the
black/white wires to 12volts and the other to the door pin wire. For negative connect one of the
black/white wires to ground and the other to the door pin wire.