Cambridge Audio 540d v2 Manuale Utente

540D V2

azur

ENGLISH

There is no power

Ensure the AC power cord is connected securely.

Ensure the plug is fully inserted into the wall socket and is switched on.

Check fuse in the mains plug or adaptor.

The player will not read the disc

Check the disc is not loaded upside down.

Check that the disc is not too scratched or dirty.

The disc type is unsupported by this unit (e.g. MP3, DVD-A, SACD etc).

There is no sound

Ensure that the amplifier is set correctly.

Check that the interconnects are inserted correctly.

The disc is skipping

Check that the disc is not too scratched or dirty.

Ensure the player is on a firm surface and not subject to vibrations.

A low hum or buzz sound can be heard

Power cords or lighting placed near this product.

Analog inputs not connected securely.

No sound from the rear speakers

Source being played is not recorded in surround-sound.

A stereo mode has been selected.

No sound from the centre speaker

A stereo mode has been selected.

No sound from the subwoofer

DD PLII mode (which has no LFE channel) has been selected with all

speakers set to ‘Large’.

Remote control is not working

The batteries are flat.

The remote is too far from the unit or out of the effective range.

Troubleshooting

The 540D V2 features a Control Bus input/output

that allow un-modulated remote control

commands (positive logic, TTL level) to be received

electrically by the unit and looped to another unit

if desired. These control commands are typically

generated by custom installation (multi-room)

systems or remote IR receiver systems. The Control Bus sockets are

colour-coded orange.
An IR Emitter Input is also provided that allows modulated IR remote

control commands to be received electrically by the unit. Commands on

this input operate the unit only and are not looped out demodulated on

the Control Bus Output. This feature is useful for multi-room systems

(such as the Cambridge Audio Incognito multi-room system) which

feature routed I.R. emitter outputs. Instead of using window emitters

stuck over the CD players front panel IR receiver, a mono 3.5mm mini-

jack to 3.5mm mini-jack lead can be used for a more reliable electrical

connection.
The 540D V2 also features a ‘direct’ IR/Control code for On/Off that can

be accessed on the supplied remote control for teaching into C.I.

systems as follows:
Press and hold the Standby button. The remote first generates it's

standby (toggle) command. Keep the button held down, after 12

seconds a DVD player “On” command will be generated. If the button is

kept held down for a further 12 seconds, a DVD player “Off” command

is generated.
A full code table for this product is available on the Cambridge Audio

website at: www.cambridge-aaudio.com

Custom installation (C.I.) use

IR Emitter

Out

Control Bus

Disc types

CD (CD-DA), DVD-V, CD-R/RW,

DVD-R/RW, DVD+R/RW, DivX, MP4

DAC architecture

Crystal/Cirrus Logic CS4382

8-channel (5.1 + 2ch Stereo) 24 Bit

Analog audio outputs

• Stereo

• 5.1 (from DD or PLII)

Analog video outputs

• Composite Video (CVBS)

• S-Video (SVHS)

• RGB/SCART

• Component (YCbCr/YPbPr)

HDMI output

Scaling/Deinterlacing to 480p, 576p,

720i/p, 1080i

THD (unweighted)

< 0.002% @ 1kHz

< 0.008% @ 20Hz - 20kHz

IMD (19/20kHz) 0dBFs

< 0.002%

S/N ratio

< -103dB

Crosstalk @1kHz

< -103dB @ 1kHz

Dynamic Range

> 105dB

Frequency response

5Hz - 20kHz ± 0.2dB

Jitter (correlated)

< 140 psec

Composite Video

1.0V pk-pk (75 ohms)

S-VVideo

Y: 1.0V pk-pk (75 ohms)

C: 0.286V pk-pk (75 ohms)

Component Video

Y: 1.0V pk-pk (75 ohms)

Cb/Cr: 0.75V pk-pk (75 ohms)

Pb/Pr: 0.75V pk-pk (75 ohms)

Power supply

100-240V AC ~ 50/60Hz

Max power consumption

25W

Dimensions (H x W x D)

70 x 430 x 310mm

Weight

3.8kg (8.4Lbs)

Technical specifications