Craftsman 486.245071 Manuale Utente
16
FIGURE 24
Holding the adapter bracket and the deck adapter
•
together, position the deck adapter on the mower
deck. Keeping the edge of deck adapter as close as
possible to the offset in the adapter bracket, see if the
slot in the adapter bracket can be aligned with one
or two of the deflector holes in your mower deck’s
discharge opening. If the bracket can not be located
correctly using existing holes, it will be necessary to
drill one or two 5/16" diameter holes in the deck. See
figure 25.
deck. Keeping the edge of deck adapter as close as
possible to the offset in the adapter bracket, see if the
slot in the adapter bracket can be aligned with one
or two of the deflector holes in your mower deck’s
discharge opening. If the bracket can not be located
correctly using existing holes, it will be necessary to
drill one or two 5/16" diameter holes in the deck. See
figure 25.
Position the adapter over the deck opening, and
•
check for fit of cutout as shown in figure 24. Trim
cutout, if necessary, to allow tilting of adapter, keeping
the fit as close as possible for best vacuum suction.
cutout, if necessary, to allow tilting of adapter, keeping
the fit as close as possible for best vacuum suction.
MOWER DECK
DECK ADAPTER
NOTE: Make sure adapter clears gauge
wheels on mower deck
wheels on mower deck
Curl on deck may be located outside of adapter
or inside depending on deck opening design
or inside depending on deck opening design
DECK ADAPTER
MOWER DECK
ADAPTER BRACKET
Keep edge of adapter as close
as possible to offset in bracket
as possible to offset in bracket
Use existing holes or drill 5/16"
diameter hole or holes.
diameter hole or holes.
FIGURE 25
ASSEMBLING THE #62468 DECK ADAPTER
TO THE MOWER DECK
TO THE MOWER DECK
CAUTION: Mower deflector must be
replaced when Vac System deck adapter
is removed. Do Not operate mower
unless adapter or deflector is in place and
properly mounted.
replaced when Vac System deck adapter
is removed. Do Not operate mower
unless adapter or deflector is in place and
properly mounted.
NOTE: Not all of the parts in the deck adapter hardware
package will be needed for your particular fit up.
Remove the mower discharge deflector from your
•
mower deck. Save the deflector and hardware for
remounting deflector.
remounting deflector.
1/4" DOWN
Keep cut-off as close to
the top edge as possible.
the top edge as possible.
IMPORTANT:
1/2" FROM FRONT
Identify and cut out the template for your
•
brand and
size mower deck. If there is no template included for
your deck size, you can make your own template by
marking around a piece of cardboard held against the
edge of the deck's discharge opening.
your deck size, you can make your own template by
marking around a piece of cardboard held against the
edge of the deck's discharge opening.
Tape the template to the face of the adapter, about
•
1/2" from front and 1/4" down from top for deeper
decks. For shallow decks, position template low
enough that adapter will not extend below bottom
of deck. Mark outline of template on face of adapter
using white crayon, nail or scriber. Drill a starting hole
inside the outline, then use a saber saw or key hole
saw to cut out the opening. See figure 23.
decks. For shallow decks, position template low
enough that adapter will not extend below bottom
of deck. Mark outline of template on face of adapter
using white crayon, nail or scriber. Drill a starting hole
inside the outline, then use a saber saw or key hole
saw to cut out the opening. See figure 23.
FIGURE 23
BEFORE PROCEEDING, look in the yellow fold-out sheet to find the template
for Sears mower decks (look in the white fold-out sheets for additional decks). If
written instructions are printed on the template, follow those instructions instead
of the instructions in this manual.
for Sears mower decks (look in the white fold-out sheets for additional decks). If
written instructions are printed on the template, follow those instructions instead
of the instructions in this manual.
STOP