Champion Manufacturing d1eb036 Manuale Utente
173858-YIM-A-0306
Unitary Products Group
3
GENERAL
Model D1EB units are factory assembled cooling only air con-
ditioners designed for outdoor installation on a rooftop or a
slab.
ditioners designed for outdoor installation on a rooftop or a
slab.
The units are completely assembled on rigid, but easily
removable base rails. All piping, refrigerant charge, and elec-
trical wiring is factory installed and tested. The units require
only electric power and duct connections at the point of instal-
lation.
removable base rails. All piping, refrigerant charge, and elec-
trical wiring is factory installed and tested. The units require
only electric power and duct connections at the point of instal-
lation.
INSPECTION
As soon as a unit is received, it should be inspected for possi-
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing. Refer to Form 50.15-NM for additional
information.
information.
REFERENCE
Additional information on the design, installation, operation
and service of this equipment is available in the following ref-
erence forms:
and service of this equipment is available in the following ref-
erence forms:
•
173858 - General Installation
•
036-21686-001 - Technical Guide
REPLACEMENT PARTS
Refer to Replacement Parts Manual for complete listing of
replacement parts on this equipment.
replacement parts on this equipment.
INSTALLATION
LIMITATIONS
These units must be installed in accordance with the follow-
ing national and local safety codes.
ing national and local safety codes.
1.
National Electrical Code ANSI/NFPS No. 70 or Canadian
Electrical Code Part 1, C22.1 (latest editions).
Electrical Code Part 1, C22.1 (latest editions).
2.
Local plumbing and waste water codes and other appli-
cable local codes.
cable local codes.
Refer to Table 1 for unit application data.
If components are to be added to a unit to meet local codes,
they are to be installed at the dealer's and/or the customer's
expense.
they are to be installed at the dealer's and/or the customer's
expense.
Size of unit for proposed installation should be based on heat
loss/heat gain calculations made in accordance with industry
recognized procedures identified by the Air Conditioning
Contractors of America.
loss/heat gain calculations made in accordance with industry
recognized procedures identified by the Air Conditioning
Contractors of America.
LOCATION
Use the following guidelines to select a suitable location for
these units.
these units.
1.
Unit is designed for outdoor installation only.
2.
Condenser must have an unlimited supply of air. Where
a choice of location is possible, position unit on either
north or east side of building.
a choice of location is possible, position unit on either
north or east side of building.
3.
For ground level installation, a level pad or slab should
be used. The thickness and size of the pad or slab used
be used. The thickness and size of the pad or slab used
D
1
E
B
A
PRODUCT NOMENCLATURE
PRODUCT GENERATION
1 = NEW or Current Design
PRODUCT CATEGORY
D = Single Package Air Conditioner
(Air Cooled)
PRODUCT IDENTIFIER
EB
3
0
6
5
0
FACTORY
INSTALLED ELECTRIC HEAT
A = No Electric Heat Installed
VOLTAGE CODE
50 = 380/415-3-50
NOMINAL COOLING
CAPACITY (MBH)
036 = 36,000 BTUH
048 = 48,000 BTUH
060 = 60,000 BTUH
048 = 48,000 BTUH
060 = 60,000 BTUH
TABLE 1:
UNIT APPLICATION DATA
Wet Bulb Temperature (°C) of Air on
Evaporator Coil, Min. / Max.
Evaporator Coil, Min. / Max.
14 / 22
Dry Bulb Temperature (°C) of Air on
Condenser Coil, Min.
1
/ Max.
1.
A low ambient accessory is available for operation
down to 0°F.
down to 0°F.
7 / 49