Network Computing Devices ncd-6029-3 Manuale Utente
2172
21-8136 09-07 NCD-6029-3
I
NSTALLATION
INSTRUCTIONS
Congratulations - your new Air Helper Springs are quality
products capable of improving the handling and comfort of
your vehicle. As with all products, proper installation is the
key to obtaining all of the benefits your kit is capable of
delivering. Please take a few minutes to read through the
instructions to identify the components and learn where and
how they are used. It is a good idea to start by comparing the
parts in your kit with the parts list below.
your vehicle. As with all products, proper installation is the
key to obtaining all of the benefits your kit is capable of
delivering. Please take a few minutes to read through the
instructions to identify the components and learn where and
how they are used. It is a good idea to start by comparing the
parts in your kit with the parts list below.
The heart of the air helper spring kit is, of course, the air
springs. Remember that the air helper springs must flex and
expand during operation, so be sure that there is enough
clearance to do so without rubbing against any other part of
the vehicle.
expand during operation, so be sure that there is enough
clearance to do so without rubbing against any other part of
the vehicle.
Be sure to take all applicable safety precautions during the
installation of the kit. The instructions listed in this brochure
and the illustrations all show the left, or driver’s side of the
vehicle. To install the right side assembly simply follow the
same procedures.
and the illustrations all show the left, or driver’s side of the
vehicle. To install the right side assembly simply follow the
same procedures.
Your kit includes separate inflation valves and air lines
for each air helper spring. This will allow you to level your
vehicle from side to side as well as from front to back. If you
would rather have a single valve inflation system, your
dealer can supply the required "T" fitting.
vehicle from side to side as well as from front to back. If you
would rather have a single valve inflation system, your
dealer can supply the required "T" fitting.
I
MPORTANT
!
For your safety and to prevent possible damage to your
vehicle, do not exceed the maximum load recommended by
the vehicle manufacturer (GVWR). Although your Air Helper
Springs are rated at a maximum inflation pressure of 100
psi, this pressure may allow you to carry too great a load on
some vehicles. It is best to have your vehicle weighed once
it is completely loaded and compare that weight to the
maximum allowed. Check your vehicle owner’s manual for
maximum loads listed for your vehicle.
the vehicle manufacturer (GVWR). Although your Air Helper
Springs are rated at a maximum inflation pressure of 100
psi, this pressure may allow you to carry too great a load on
some vehicles. It is best to have your vehicle weighed once
it is completely loaded and compare that weight to the
maximum allowed. Check your vehicle owner’s manual for
maximum loads listed for your vehicle.
When inflating your Air Helper Springs, add air pres-
sure in small quantities, checking pressure frequently dur-
ing inflation. The air spring requires much less air volume
than a tire and, therefore, inflates much quicker.
ing inflation. The air spring requires much less air volume
than a tire and, therefore, inflates much quicker.
T
OOLS
R
EQUIRED
• (2) 9/16" E
ND
W
RENCHES
• 5/16" D
RILL
B
IT
• (2) 1/2" E
ND
W
RENCHES
• 3/8" D
RILL
B
IT
• U
TILITY
K
NIFE
• E
LECTRIC
D
RILL
WARNING:
Do not inflate this assembly when it is
unrestricted. The assembly must be restricted
by the suspension or other adequate structure.
Do not inflate beyond 100 psi Improper use or
over inflation may cause property damage or
severe personal injury.
by the suspension or other adequate structure.
Do not inflate beyond 100 psi Improper use or
over inflation may cause property damage or
severe personal injury.
AIR SPRING
9001
2
UPPER BRACKET
5376
2
LOWER BRACKET
5092
2
BRACKET STRAP/SHIM 1/2"
5086
4
BRACKET STRAP/SHIM 1"
5093
4
AIR LINE TUBING
1
3/8"-16 FLANGE LOCK NUT
16
3/8"-16 X 3/4" FLANGE HEX BOLT
6
3/8"-16 x 4-1/2" CARRIAGE BOLT
8
3/8" SPECIAL WASHER
6
3/8" FLAT WASHER
2
3/8"-16 X 1 1/2 HEX BOLT
8
5/16" FLAT WASHER
4
PUSH-TO-CONNECT
INFLATION VALVE
2
INFLATION VALVE CAP
2
PUSH-TO-CONNECT
ELBOW FITTING
2
THERMAL SLEEVE
2
NYLON TIE
6
CAUTION TAG
2
P
ARTS
LIST
Installation of this kit requires a
minimum of 6-1/2" of clearance between
the tire side wall and the frame.
D
O
NOT
INSTALL
THIS
KIT
ON
VEHICLES
WITH
COMPOSITE
LEAF
SPRINGS
. T
HIS
KIT
IS
COMPATIBLE
WITH
STEEL
LEAF
SPRINGS
ONLY
.