Manualsbrain.com
  1. Manuali
  2. Marche
  3. Honeywell
  4. HD40
  5. Manuale Utente

Honeywell HD40 Manuale Utente

Scarica
Pagina di 1
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total/Effective Pixels No.
S/N Ratio
Resolution
Video Output Level
Lens- Mirror Cover
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
Input/Output Connector
Power Consumption
Dome Size (Ø)
Weight
NTSC : 525 Lines                  PAL : 625 Lines
2 : 1 Interlace
15.734kHz                           15.625kHz
59.94Hz                                 50Hz  
1/3 inch SONY Super HAD CCD
  270K/250K                           320K/290K  
More than 48dB
380 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=3.8mm)
Manual
Internal
0.1 Lux
 1/60~100,000 Sec.              1/50~100,000 Sec.
Auto
Auto
Power (Red Jack), Video (Yellow Jack)
12VDC (10V~15V), 0.15A / 1.8W (Max)
85mm
Approx. 210g
This manual explains the installation and operating method for the 
 color dome camera. Before installation, make sure you are familiar 
 with this product's special features and proper operating technique.
!
USER INFORMATION:
PRECAUTION:
Design and specifications 
are subject to change 
without notice.
INSTALLATION:
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE 
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
All the warnings and instructions of this manual should be followed.
Keep enough space around the unit for ventilation. 
Slots and openings on the monitor should not be blocked.
During flashes of lightning or cracks of thunder, or when the system 
is not used for a long time, unplug the system power supply to 
protect the unit from lightening or power surges.
Do not attempt to service this unit yourself as opening or removing 
covers may you to dangerous voltage or other hazards. Please refer 
all servicing to qualified service personnel.
Do not place anything on top of the unit that might spill or fall into it.
To reduce the risk of fire or electric shock, do not expose this appliance 
to rain or moisture.
Remove the plug from the outlet before cleaning. Do not use liquid 
aerosol detergents. Use water damped cloth for cleaning.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM 
OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT 
TO RAIN OR MOISTURE"
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
Explanation of two Symbols
     Insert coin to the side 
hole and remove the 
dome cover by twist coin.
NOTE
Operation Manual
Dome Camera
Mounting Screw
The image does not 
appear on the screen.
Check the power source for the monitor 
and camera and ensure that the voltage 
and polarity are properly connected and 
being supplied correctly.
The image on the 
screen is dim.
Check if the lens is stained. If dirty, 
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not 
work properly, the surface 
of the camera case is hot, 
and a black line appears 
on the screen.
Check if you have connected the camera 
to a proper power source and If there is 
no problem with the power, turn the unit 
off immediately and seek assistance from 
our Customer Service department.
The screen blinks a lot.
Check if the camera is pointed toward 
the sun or a fluorescent lamp.
Adjust the angle or location of the 
camera if too much light is coming into 
the screen.
Draw out power/video wires to the connecting 
places.
3
Stick the guide pattern on the wall or ceiling.
1
Adjust desired focus and scene by turning 
and moving the 3-axis camera bracket by 
hand.
5
Drill two holes according to the guide pattern 
then insert anchors into the drilled holes.
2
Put the dome cover over the base.
6
Fix the dome cover on the base by covering.
7
Fixed the camera to a celling using two screws.
4
Guide Pattern
TROUBLESHOOTING:
If you have trouble operating 
 your camera, refer to the following. 
 If the guidelines do not enable you to solve the problem, 
  contact an authorized technician.
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
12VDC(10V~15V),
1.8W(Max)
Terminal Color
Yellow
Red
• The wire is polarized. 
• Use 12VDC     power source.
12VDC Power Type
Video Output
GND
#1
#2
Video
(Yellow)
Power 
- 12VDC
 
(Red)
Ceiling
Dome Cover
Guide Pattern
Dome Base
Mounting 
Screw
COMPOSITION:
CONNECTION:
DIMENSIONS:
SPECIFICATIONS:
360º
90º
360º
Horizontal
Pan
Tilt
    Built-in             camera 
bracket makes it much 
easier to rotate in any 
direction.
3-axis
4.45”
(113 mm)
3.35”
(85 mm)
1.34”
(34 mm)
1.68”
(42.7 mm)
3.02”
(76.7 mm)
2- 0
.18
”
(4.
5 m
m)
3.35”
(85 mm)
P/N:3810-0071G
Rev 0 03/18
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
www.honeywellvideo.com
• 1/3” SONY Super HAD CCD
• 380 TV Lines Resolution
• Built-in Fixed Lens (f=3.8mm) 
• Min. Illumination : 0.1 Lux 
• Auto White Balance
• Diameter of Bubble : 85mm
• Easy Install (3-Axis)
Operation
Manual
HD40
Series
READ AND KEEP THIS
OPERATION MANUAL
   
   
   
  
  
  
  
  
  
  
  
  
•S
im
ple  to insta
ll