dls 1269 Manuale Utente
TWEETER INSTALLATION T20
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
Technical Assistance
For technical assistance ask the shop where the product
was sold or the distributor in your very country.You can
always phone the DLS Helpdesk in Sweden + 46 31
840060 or send an e-mail to info@dls.e
Information can also be found on our WEB-site www.dls.se
was sold or the distributor in your very country.You can
always phone the DLS Helpdesk in Sweden + 46 31
840060 or send an e-mail to info@dls.e
Information can also be found on our WEB-site www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
development. For this reason all or part of specifications
& designs may be changed without prior notice.
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
T20 can be mounted on the dashboard with the plain cup (1), the
angled cup (2), or recessed in a doorside. These tweeters are
included in the C4, C5, C6 and C36 speaker kits.
angled cup (2), or recessed in a doorside. These tweeters are
included in the C4, C5, C6 and C36 speaker kits.
SURFACE MOUNTING:
Plain mounting: Use only the plain mounting cup (1) (it´s normally
mounted at delivery). Attach to surface with the two screws or double
adhesive tape.
Angled mounting
mounted at delivery). Attach to surface with the two screws or double
adhesive tape.
Angled mounting
: Remove the plain mounting cup by bending with a
small screw driver in the gap (A). Attach the tweeter element to the
angled cup (2) as shown on picture 3. Pull the cable through the cen-
ter hole. Now the tweeter can be mounted in two different angles.
Attach to the surface with the two screws or double adhesive tape.
angled cup (2) as shown on picture 3. Pull the cable through the cen-
ter hole. Now the tweeter can be mounted in two different angles.
Attach to the surface with the two screws or double adhesive tape.
RECESSED MOUNTING:
Drill a hole in the door side with a diameter of 48 mm /1,89". The in-
stallation becomes easier if the door side is removed from the door.
Put the two metal wings through the two tracks in the center of the
cup, just as the picture shows, and attach them with the M4 screw
and nut through the center hole. Put the tweeter element into the cup
with the cable going out through the bottom hole. Attach the tweeter
element to the plain cup using the mounting ring (C) attached between
the cup and the tweeter element. The metal wings (B) should be on
the back side of the door panel, holding the cup in place.
stallation becomes easier if the door side is removed from the door.
Put the two metal wings through the two tracks in the center of the
cup, just as the picture shows, and attach them with the M4 screw
and nut through the center hole. Put the tweeter element into the cup
with the cable going out through the bottom hole. Attach the tweeter
element to the plain cup using the mounting ring (C) attached between
the cup and the tweeter element. The metal wings (B) should be on
the back side of the door panel, holding the cup in place.
A
2
1
3
TWEETER INSTALLATION T16
T16 can be mounted on the dashboard with the angled cup (1), or
recessed in a doorside. These tweeters are included in the B5 and B6
speaker kits.
recessed in a doorside. These tweeters are included in the B5 and B6
speaker kits.
SURFACE MOUNTING:
Angled mounting
: Put the cable through the hole in the rear end of
the angled cup. The tweeter is attached to the cup by pressing them
together. Attach the cup to the surface with the double adhesive tape.
together. Attach the cup to the surface with the double adhesive tape.
RECESSED MOUNTING:
You need a hole with a diameter of 43 mm/ 1,7”. Put the two metal
wings through the two tracks in the center of the cup, just as the
picture shows, and attach them with the M4 screw and nut through
the center hole. The cup is attached to the door side when the metal
wings is pressed to the back side of the door.
Put the tweeter element into the cup with the cable going out through
the bottom hole. Then attach the element by putting it into the cup.
wings through the two tracks in the center of the cup, just as the
picture shows, and attach them with the M4 screw and nut through
the center hole. The cup is attached to the door side when the metal
wings is pressed to the back side of the door.
Put the tweeter element into the cup with the cable going out through
the bottom hole. Then attach the element by putting it into the cup.
1
2
3
4
B
C
Size
20 mm / 0,8"
Nom. power (RMS)
50 Watts, 80 Watts max
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
20 mm / 0,8"
neodymium magnet
Mounting depth
20 mm / 0,8"
(recessed mounting)
Mounting hole
48 mm / 1,89" (recessed mounting)
Cone material
Silk
FACTS ABOUT DLS T20 TWEETER
Size
16 mm / 0,63"
Nom. power (RMS)
50 Watts, 80 Watts max
Freq. range
2 kHz-20 kHz
Sensitivity
91 dB
Magnet diameter
20 mm / 0,8"
neodymium magnet
Mounting depth
20 mm / 0,8"
(recessed mounting)
Mounting hole
43 mm / 1,7"
(recessed mounting)
Cone material
Mylar
FACTS ABOUT DLS T16 TWEETER
A