Carvin original-floyd-rose Manuale Utente

• Loosen strings completely by turning machine

heads.

• Loosen the string lock thumb screws counter

clockwise on the back of the Sperzel gears.
You only need to turn these screws about 2 or
3 turns.

• Loosen saddle lock screws with 3mm allen

wrench.

• Remove strings.
• Remove broken string bits from lock box with

small magnetic screwdriver or long nose
tweezers.

• Normalize the tremolo fine tuners to the mid

point of their travel.

• Cut ball ends and extra wraps off of the new

strings.

• Insert new strings into lock box, sandwiched

between lock box wall and lock block.

• Tighten saddle lock screws real snug, but do

not over tighten them.

• Slide string through the small hole in the

string post.  Take up all the slack then tighten
the thumb screw on the back.  Cut off the
excess string and then tune your guitar.

• Tune up from low E (6th) string to high E (1st)

string, 6 or 7 times in order to stretch the
tremolo springs.

• Stretch your strings using the tremolo arm.
• When strings hold their pitch relative to each

other, then tuning is complete.

• Fine tune using the fine tuners.

Lock Block

Arm Cap Nut

• Slide tremolo arm into socket..

• Turn the arm cap nut clockwise about 4 turns

until it stops.

• If you want your arm to stay up then tighten the

cap nut fairly tight.  If you want your arm to
swing freely then back off slightly on the cap nut.

• Remove arm when transporting or storing guitar

in its case.

• Oil socket with a drop of 3 in 1 oil twice a year

or more.

• Turn string height studs C.W. to lower action.
• Turn string height studs C.C.W. to raise action.

Your Carvin guitar comes set up with a set of high
quality 942 strings.  If you continue to use the
same brand and gage of strings, spring tension
adjustment is normally not necessary.  However, if
you switch brands or gages you may need to re-
adjust spring tension.  Follow the steps below.

1. Tune up guitar to pitch.
2. Remove rear cover plate.
3. If tremolo rear end is to high in the air follow

steps #4,5,6 & 11.

4. Tighten the two screws on the rear of the guitar

that hold the spring claw,  

1

/

2

turn each with a

phillips #2 driver.

5. Re-tune guitar and see if tremolo is parallel with

guitar body.

6. If it’s just right, go to step #11.  If it’s still to high

repeat steps #4 & 5.

7. If tremolo rear end is setting to low in the

tremolo cavity follow steps #8, 9, & 10.

8. Loosen the two screws that hold the spring

claw, 

1

/

2

turn each with a phillips #2 driver.

9. Re-tune and see if tremolo is parallel with guitar

body.

10. If it is just right, go to step #11.  If it’s still to

low repeat steps #8 & 9.

11. Put rear cover plate back on.

• When turning the two claw screws, have your

guitar face down on a padded table.

• Hold screw driver firmly when turning, so as not

to slip off screw head and scratch the back of
your guitar.

800-854-2235 or www.carvin.com

Saddle Lock Screws

(3mm wrench)

Intonation Screws (2.5mm wrench)

• Don’t rest palm on tremolo while tuning up or

fine tuning.

• Over tightening of saddle lock screws can cause:

Lock box walls to crack, distortion of shape of
the lock block, rounding of allen sockets, and, or
cause rapid string breakage.

• When stringing up the Sperzel tuners do not

wrap multiple string wraps around the post.
Eliminate as many wraps as possible to keep
your guitar in better tune. 

1

/

2 

of a turn around the

string post should be considered maximum.

Saddle

Lock Box

Fine Tuners

String height Studs (3mm wrench)

The Original Floyd Rose is the most rugged and dependable locking tremolo made today.  With replacement
parts available at most guitar repair shops, the serviceability and playability can’t be beat, and will stay that way
for years to come.

Adjustment Screws (use #2 phillips screwdriver)

Spring Claw

Springs

Tremolo Sustain Block

If the arm socket becomes loose,
tighten with a 3mm allen wrench.