Mobotix PTMount Manual Pan/Tilt Guida Specifiche

The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high-resolution video 
systems cost-efficient.

Security-Vision-Systems

31.988_EN_V2_12/2014

•  S15D: Modular PoE network camera with max. two sensor modules for con-

cealed installation (not included)

•  All components weatherproof (S15D: IP65, sensor modules IP66), 

–30 to +60 °C/–22 to +140 °F

•  Day and Night sensor modules can be freely combined

•  Sensor module connection cables max. 2 m each (e.g., for indoors/outdoors)

MOBOTIX S15D 

with 2 sensor modules, each in 

PTMount

MX-PTMount-OPT

1.1

1.2

1.9

1.3

1.4

1.1

1

Sphere with rotating insert (installed)

1.2

1

Foot (installed)

1.3

1

Base plate (installed)

1.4

1

Swivel ring (installed)

1.5

1

Sealing

1.6

4

Washer Ø 4.3 mm, stainless steel

1.7

4

Wood screw 4x40 mm, stainless steel

1.8

4

Screw anchor S6

1.9

1

Allen wrench 2.5 mm

•  Using the 2.5 mm Allen wrench, re-

move the two screws that hold the 
foot onto the swivel ring.

•  Remove the swivel ring and the base 

plate.

•  Make sure that there is enough space 

for installing the PTMount and that 
you can access it from the rear later 
on. The surface should be even and 
smooth so that the sealing lies flat 
properly.

•  Drill the holes for the base plate (drilling 

template see 

•  In the center of the drilling template, drill 

another hole into the wall or faceplate 
for the sensor cable. Since you will 
push the hinged ferrite through this 
hole later on, the hole should have 
a diameter between 15 and 35 mm.

•  Insert the screw anchors into the holes, 

if required.

106 mm

•  Hold the sealing, the swivel ring and 

the base plate as shown in the figure.

•  Attach the base plate using the sup-

plied wood screws and washers.

•  When tightening the screws, make 

sure that you can still rotate the swivel 
ring by hand.

•  Carefully guide the sensor cable 

through the sealing, the swivel ring 
and the base plate, then attach the 
hinged ferrite to the cable.

•  Push the sensor cable into the wall/

ceiling so as to completely hide the 
ferrite.

•  Guide the sensor cable from the back 

into the foot and the sphere.

•  Use the two screws to affix the foot 

and sphere assembly to the swivel 
ring and make sure that the foot can 
still be rotated.

•  Loosen the two fastening screws of 

the insert (

), then rotate the insert 

so that the small bar opposite of the 
TOP/OBEN label points to the hole of 
the grub screw (

).

•  Secure the insert against rotating by 

tightening the two fastening screws 
using the 2 mm Allen wrench.

•  Attach the sensor module cable to 

the sensor module (turn blue bayonet 
catch to the left and remove, pull out 
the plug, connect the sensor cable, 
apply bayonet catch and lock by turn-
ing to the right).

•  Push the sensor module into the 

PTMount so that the 

MOBOTIX let-

tering is turned 90 degrees to the left 
vs. the 

TOP/OBEN lettering.

•  Using the module wrench (red or black), 

lock the sensor module by turning it 
90 degrees to the right.

•  Secure the sensor module by tighten-

ing the grub screw using the 2 mm 
Allen wrench. The grub screw locks 
the sensor module within the insert 
and prevents inadvertent unlocking 
of the sensor module.

•  Adjust the sensor module temporarily 

by pointing it into the desired viewing 
direction.

•  Make sure that the 

TOP/OBEN label on 

the insert is pointing upwards. If this is 
not the case, loosen the two fastening 
screws using the 2 mm Allen wrench 
and rotate the insert. Lightly tighten 
the two fastening screws.

Continue to bring the camera into service as described in 

.

±180°

±180°

100°

1.5

1.8

1.7

1.6

±180°

Panning

±180°

Rotating

100°

Tilting

Mounting to a Ceiling

Mounting upright

Mounting to a Wall