BOSS Reflex BRRF46 Manuale Proprietario

 1 - BRRF46 Overhead Speaker System

 1 - Bluetooth Multi-Function Controller Kit

 2 - 1.75” / 2.00” Rollbar Mounting Kit

 1 - Quick Connect Power Cable

 1 - User Manual Quick Start Guide / Poster

 1 - Warranty Card / Facebook Card

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: 

(1) this device may not cause interference, and 
(2) this device must accept any interference, including interference that may cause 
undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other 
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by 
user. This equipment complies with FCC/ IC radiation exposure limits set forth for 
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure 
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should 
be installed and operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration 
RUPRGL¿FDWLRQVFDUULHGRXWZLWKRXWDSSURSULDWHDXWKRUL]DWLRQPD\LQYDOLGDWHWKH
user’s right to operate the equipment. 

NOTE: This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guar-
antee that  interference will not occur in a particular installation. If this equipment 
does cause harmful interference to radio or television reception, which can be 
GHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRႇDQGRQWKHXVHULVHQFRXUDJHGWRWU\WR
correct the interference by one or more of the following measures:
Ƒ5HORFDWHRUUHRULHQWWKHUHFHLYLQJDQWHQQD
Ƒ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU
Ƒ&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWGLႇHUHQWIURPWKDWWRZKLFKWKH
receiver is connected.
Ƒ&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS

 

GETTING TO KNOW YOUR

BRRF46 MULTIFUNCTION CONTROLLER (MFC)

Ŷ

'RQRWRSHUDWHPRELOHHTXLSPHQWZKLOHGULYLQJDPRWRUL]HGYHKLFOH±VDIHGULYLQJDQG

safety consideration of others should always be your highest priority

Ŷ

 In the event you should notice smoke, strange noises or odor from this product, or any 

RWKHUDEQRUPDOVLJQVLPPHGLDWHO\WXUQRႇWKHSRZHUDQGFRQVXOW\RXUGHDOHURUWKHQHDUHVW
DXWKRUL]HGBOSS AUDIO Service Center. Using this product in this condition may result in 
permanent damage to the system

Ŷ

 Set your volume control at a low setting, then slowly increase the sound until you can 

hear it comfortably without distortion, or ear discomfort

Ŷ

 BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

- Do not turn up the volume so high that you can’t hear what’s around you
8VHFDXWLRQRUWHPSRUDULO\GLVFRQWLQXHXVHLQSRWHQWLDOO\KD]DUGRXVVLWXDWLRQV

Ŷ

 Do not attempt to install or service this product by yourself. Installation or servicing of this 

product by persons without professional training and experience in electronic equipment 
DQGPRWRUL]HGYHKLFOHDFFHVVRULHVPD\EHGDQJHURXVDQGFRXOGH[SRVH\RXWRWKHULVNRI
HOHFWULFVKRFNLQMXU\RURWKHUKD]DUGV

Ŷ

5HIHUDQ\UHSDLUVWRDTXDOL¿HGBOSS AUDIO SYSTEMS Service Center

Ŷ

 The BRRF46 should be hard wired directly to the main vehicle battery 

Ŷ

 When wiring directly to the vehicles battery, be sure to disconnect the batteries negative 

terminal wire before starting any wiring procedures

Ŷ

 The ground cable length should be short as possible (See wiring diagram)

Ŷ

 The BRRF46 has a weather resistant design, it should not be under any circumstances 

submerged in, or under water

Ŷ

 Use only the supplied installation parts provided with the BRRF46

Ŷ

 Wash with a mild detergent and lukewarm water using a clean sponge or a soft cloth

Ŷ

 Rinse well with clean water

“DO NOT’S” - Very Important
Ŷ

 DON’T clean in hot sun or on very hot days 

Ŷ

 DON’T use abrasive or highly alkaline cleaners on the main body

Ŷ

'21¶7VFUDSHWKHPDLQERG\ZLWKUD]RUEODGHVRURWKHUVKDUSLQVWUXPHQWV

Ŷ

 DON’T ever use, gasoline, acetone or carbon tetrachloride

Ŷ

 DON’T ever use a pressure washer aimed at the speakers

 

1) Power on the MFC by long-pressing the 

 Power button for 3 seconds, long-press the 

 Bluetooth button for 3 seconds, the BLUE LED

ZLOOVWDUWWRUDSLGO\ÀDVKVLJQDOOLQJWKDW

the MFC is now ready for Bluetooth pairing

NOTE: You have 2 minutes before you must restart this procedure over again.
 
2) The MFC is now in pairing mode:

ANDROID users:
 

a. Go into the Settings Menu of your device

 

b. Enter the Bluetooth Menu

c. TURN ON Bluetooth and press SCAN

 d. 

“BOSS REBEL UTV” will now be displayed under AVAILABLE DEVICES

 

e. If prompted, enter passcode: “0000”

iOS users:
 

a. Go into the Settings Menu of your iOS device

 

b. Enter the Bluetooth Menu

c. TURN ON Bluetooth

 d. 

“BOSS REBEL UTV” will now be displayed

 

e. If prompted, enter passcode: “0000”

3) If BOSS REBEL UTV is not seen, repeat the above steps to refresh the “Device List”

4) When the connection is successful a tone will be heard, and the Bluetooth LED indicator 
will light solid, you are now ready to stream music from your favorite media player to the MFC

Using this product without running the engine can drain the battery. 

 

 

To avoid battery exhaustion, be sure to occasionally run the

 

 

vehicles engine while using this product. 

 

1) Power on the MFC and your last paired device Bluetooth.

2) Ensure you are within range of the MFC, the unit will now automatically reconnect

3) If the device is out of range from the MFC, it will disconnect automatically:
 a. 

The 

MFC will reconnect automatically to your device when in range

4) If your device was previously paired with the MFC, but it wasn’t the last paired device:
 

a. Ensure no other devices are currently paired

 

b. Enter the Bluetooth Menu on your device being paired

 c. 

“BOSS REBEL UTV” will display under AVAILABLE DEVICES

 

d. Choose the “BOSS REBEL UTV” to reconnect

5) To clear all previously paired devices from memory, press and hold the MFC Bluetooth 
button for 10 seconds

 

 Some devices may require a manual Bluetooth reconnection once the devices 

Bluetooth is powered OFF / ON and/or back in range, repress the BOSS REBEL UTV 
button in BLUETOOTH settings on your device

1) Press the 

 PLAY/PAUSE once to start playing music or press the PLAY button from 

your devices touch screen

2) To skip songs or advance, press the  

 NEXT TRACK button

3) To select the previous song, press the 

 PREVIOUS TRACK button

4) To raise the volume press the 

 VOLUME UP button or use your devices controls

5) To lower the volume press the 

 VOLUME DOWN button or use your devices controls    

 If BLUETOOTH or AUX is disconnected for more than 10 minutes the MFC will 

automatically turn OFF, however, when not in use the ACC switch should be manually 
turned OFF to keep the vehicles main battery from draining

1) Power on the MFC by pressing and holding down the 

POWER button for 3 seconds

2) Disconnect any paired Bluetooth

GHYLFHE\WXUQLQJRႇ Bluetooth in your devices 

Settings Menu
3) Connect your 3.5mm AUX-IN cable located on front side of the MFC to your devices 
headphone jack
4) Route the wire back to MFC, secure your device in a safe location

5) To raise the volume press the 

 VOLUME UP button 

6) To lower the volume press the 

 VOLUME DOWN button 

7) To MUTE the volume press the 

 PLAY/PAUSE button 

Make sure your device Bluetooth volume is set at 100% level

 

 

before stowing your device

Make sure your device headphone volume is set at 100% level

 

 

before stowing your device

MFC can play audio from 
any device that has a 3.5mm 
headphone audio jack.

 

 

  - 

Crimp 

Tool

 

 

- Wrench or Pliers

  - 

3mm 

Allen 

Wrench

 

:KHQUHSODFLQJWKHIXVHEHVXUHWRRQO\XVHDIXVHRIWKHUDWLQJVSHFL¿HGRQ
this product. To avoid short-circuiting, cover any disconnected leads with insulating 
tape. It is especially important to insulate any unused wires, which if left uncovered
may cause a short circuit. When connecting other devices to this product, refer to 
the manual for the product to be connected. The black cable is ground, make sure 
WRFRQQHFWWKHJURXQGZLUH¿UVW(QVXUHWKDWWKHJURXQGZLUHLVSURSHUO\FRQQHFWHG
to metal parts of the vehicles body frame or direct to the battery if your vehicle 
does not have a grounded chassis frame The ground wire of this units power amp 
and a second powered system must be connected to the frame separately with 
GLႇHUHQWVFUHZV,IWKHVFUHZIRUWKHJURXQGZLUHORRVHQVRUIDOOVRXWLWFRXOGUHVXOW
LQ¿UHRUPDOIXQFWLRQ

To avoid potential shorts in the electrical 
V\VWHPEHVXUHWRGLVFRQQHFWWKH±
battery cable before installation. Use this 
XQLWZLWKD9ROWEDWWHU\DQGQHJDWLYH
grounding only. Failure to do so may result 
LQD¿UHRUPDOIXQFWLRQ

 

‡9HUVLRQ

‡$'3$95&3*$77

‡5DQJHIWP&ODVV

‡%DQG'633UHVHW(4

‡5&$/LQH2XWSXW9506

‡'LPHQVLRQ´0,'´68%

‡0,'&RQH7\SH33&DUERQ

‡7ZHHWHU6L]H´7LWDQLXP

‡0D[LPXP2XWSXW3RZHU:DWWV

‡,QSXW,PSHGDQFHNȍ

‡)UHTXHQF\5HVSRQVH+]N+]

‡2SHUDWLRQDO3RZHU9'&9DOORZDEOH

‡0$;&XUUHQW'UDZ$

‡86%&KDUJLQJ$#9'&

‡5HSODFHPHQW)XVH$$727<3(

‡&DELQHW0DWHULDO+LJK,PSDFW$%6

10.24"

(260mm)

10.24"

(260mm)

46.06"

(1170mm)

4.09"

(104mm)

Dimensions:
46.06" (1170mm) x 4.09" (104mm) x 10.24" (260mm)

Weight:
27.5 lbs (12.5 kg)

‡&RORU%ODFN
‡:HLJKWOEVNJ
‡'LPHQVLRQV,QFKHV:[+['[[
‡'LPHQVLRQVFP:[+['[[
‡6WRUDJH7HPSHUDWXUH

o

F to 175

o

F  / -15

o

&WR

o

C

‡2SHUDWLRQ7HPSHUDWXUH

o

F to 140

o

F / 0

o

C to 60

o

C

 

46

1) Determine the best location on your rollbar for your vehicle, install rubber 
bushings on the rollbar, ensure there is ample head space
2) Apply supplied Loc-Tight to allen bolt tips, let dry for 20 minutes 
3) Wrap C-clamp around rollbar, hand tighten the allen-head bolts
4) Insert left/right slide rails into REFLEX Soundbar, some vehicles will require 
the use of the rotation bracket, allowing adjustments up to +/- 10 degrees 
5) Carefully set the REFLEX Soundbar on top of the C-clamp, hand tighten the 
allen head screws
6) Center the REFLEX Soundbar, permanently tighten all the allen bolts and nuts

CAUTION: 
NEVER CONNECT THE MFC DIRECTLY 
TO THE BATTERY, ALWAYS USE AN 
ACCESSORY SWITCH

CAUTION!!
Never use USB
or AUX while in 
mud and/or water

o

OPTIONAL TOOLS NEEDED:
- Hand saw or Jigsaw