MartinLogan Motion® Vision X Manuale Proprietario
20
Your soundbar remote controls these functions:
POWER: Turns the soundbar on and off.
VOL+/VOL–: Adjusts volume level.
MUTE: When muted, the soundbar will display
‘MUTE’. Pressing this button a second time or
pressing either volume button will restore the previ-
ous volume setting.
‘MUTE’. Pressing this button a second time or
pressing either volume button will restore the previ-
ous volume setting.
MENU: Enters the soundbar menu. Exit the menu
by pushing the menu button again.
by pushing the menu button again.
BASS MODE – NIGHT: Reduces bass output
and compresses the dynamic range.
and compresses the dynamic range.
BASS MODE – BASS+: Increases bass output.
BASS MODE – NORMAL: Restores normal levels.
INPUT: Activates the selected input.
CHANGING THE REMOTE’S BATTERY
The remote control for your speaker uses two AAA
type batteries. Access the battery compartment by
using a Phillips screwdriver to remove the screw lo-
cated on the bottom of the remote.
type batteries. Access the battery compartment by
using a Phillips screwdriver to remove the screw lo-
cated on the bottom of the remote.
PROGRAMMING A SECOND REMOTE
This soundbar can be programmed to respond to
a second remote. See “The Menu System” section
of this manual for programming instructions.
This soundbar can be programmed to respond to
a second remote. See “The Menu System” section
of this manual for programming instructions.
Please note: There may be remote controls
that the soundbar cannot learn or that the sound-
bar can not learn correctly. Due to the number of
available remote controls, it is impossible to advise
which will or will not work.
that the soundbar cannot learn or that the sound-
bar can not learn correctly. Due to the number of
available remote controls, it is impossible to advise
which will or will not work.
Please note: When learning from a second remote,
you will likely find it does not have buttons that directly
correspond with all available soundbar commands.
Not all soundbar commands have to be programmed.
Some remote controls offer ‘function’ buttons (F1, F2,
etc.) that can be used to program unique soundbar
commands such as ‘NITE.MD’ or ‘OPTIC’.
you will likely find it does not have buttons that directly
correspond with all available soundbar commands.
Not all soundbar commands have to be programmed.
Some remote controls offer ‘function’ buttons (F1, F2,
etc.) that can be used to program unique soundbar
commands such as ‘NITE.MD’ or ‘OPTIC’.
Please note: Some remote controls offer discrete
‘power on’ and ‘power off’ buttons. Some offer
only a single button to toggle power on and off.
The learning function of the soundbar allows you to
program for either scenario.
‘power on’ and ‘power off’ buttons. Some offer
only a single button to toggle power on and off.
The learning function of the soundbar allows you to
program for either scenario.
R
EMOTE
C
ONTROL
T
HE
M
ENU
S
YSTEM
ENTERING AND EXITING THE MENU
To access the menu from the remote, press
‘Menu’. To exit the menu from the remote, press
‘Menu’ again or repeatedly press left until the
menu exits.
To access the menu from the remote, press
‘Menu’. To exit the menu from the remote, press
‘Menu’ again or repeatedly press left until the
menu exits.
To access the menu from the top panel, for 2 sec-
onds press and hold the center button (fig. 9). To
exit, repeatedly press the left directional button.
The menu auto exits after 30 seconds.
onds press and hold the center button (fig. 9). To
exit, repeatedly press the left directional button.
The menu auto exits after 30 seconds.
Caution! Danger of explosion
if battery is incorrectly replaced.
Replace only with the same or
equivalent type.
if battery is incorrectly replaced.
Replace only with the same or
equivalent type.