Dbx DriveRack 260 Manuale Proprietario
68
DriveRack
®
DriveRack® User Manual
Appendix A
A.4 Auto EQ Optimization Tips
By using the System Setup Wizard, crossover parameters, post-crossover parametric EQ and,
in some cases, driver alignment delay settings are set to match your system. The Auto-EQ can
be used to adjust your system to compensate for room effects, and adjust the response of the
entire system to your liking. After allowing Auto EQ to “pink the room” your system will sound
tighter. The low end will have more definition, the mids will be more intelligible, and the highs
can be tamed. Here are two things to look for to get the best performance from the Auto-EQ.
in some cases, driver alignment delay settings are set to match your system. The Auto-EQ can
be used to adjust your system to compensate for room effects, and adjust the response of the
entire system to your liking. After allowing Auto EQ to “pink the room” your system will sound
tighter. The low end will have more definition, the mids will be more intelligible, and the highs
can be tamed. Here are two things to look for to get the best performance from the Auto-EQ.
Look out for Modes
Some speaker and RTA microphone positions will result in certain frequencies canceling out.
The resulting modes can not be corrected with equalization. The Auto-EQ does not detect
modes in the frequency response, so may try to boost a band to compensate for a mode without
positive affect. You may be able to see if a lifted band is a mode by manually adjusting a
lifted EQ band - if no change in the EQ is perceived, you probably are seeing a mode in your
frequency response. To reduce the effect of this mode, try different microphone positions and
adjust the location of your speakers, then re-pink the room for a more effectual Graphic EQ
adjustment.
The resulting modes can not be corrected with equalization. The Auto-EQ does not detect
modes in the frequency response, so may try to boost a band to compensate for a mode without
positive affect. You may be able to see if a lifted band is a mode by manually adjusting a
lifted EQ band - if no change in the EQ is perceived, you probably are seeing a mode in your
frequency response. To reduce the effect of this mode, try different microphone positions and
adjust the location of your speakers, then re-pink the room for a more effectual Graphic EQ
adjustment.
Adjust Crossover Output Gains (gain structure)
If your system setup or the response you have chosen results in the Auto-EQ lifting or cutting
a number of consecutive bands of the Graphic EQ, you can adjust the level of the associated
crossover output gain to match the average boost or cut in the graphic EQ and re-pink your
room. This time, the adjustment of the Graphic EQ bands will be less “heavy handed” and the
system will sound better having fewer phase problems and a lower noise floor than a more
aggressively adjusted Graphic EQ. With the rest of your system properly adjusted, the Auto EQ
can compensate for room resonance and adjust to suit personal taste without large excursions
in the Graphic EQ bands.
a number of consecutive bands of the Graphic EQ, you can adjust the level of the associated
crossover output gain to match the average boost or cut in the graphic EQ and re-pink your
room. This time, the adjustment of the Graphic EQ bands will be less “heavy handed” and the
system will sound better having fewer phase problems and a lower noise floor than a more
aggressively adjusted Graphic EQ. With the rest of your system properly adjusted, the Auto EQ
can compensate for room resonance and adjust to suit personal taste without large excursions
in the Graphic EQ bands.
Note: If using a ‘Custom’ configuration, meaning any of your amplifiers/and or speakers were
not selectable in the System Setup Wizard, it is recommend to properly tune some of the
parameters within the DriveRack 260 before using the Auto EQ feature. Failing to do so could
yield undesirable results. Therefore, it is highly recommended that the parameters contained in
the following effect modules should be tuned in the DriveRack 260 before using the Auto EQ
feature:
not selectable in the System Setup Wizard, it is recommend to properly tune some of the
parameters within the DriveRack 260 before using the Auto EQ feature. Failing to do so could
yield undesirable results. Therefore, it is highly recommended that the parameters contained in
the following effect modules should be tuned in the DriveRack 260 before using the Auto EQ
feature:
s
Appendix