Sony HT-ST5000 Manuale Proprietario
64
US
When you play content compatible
with copyright protection technology
(HDCP), it may not be output from the
system.
(HDCP), it may not be output from the
system.
Set [System Settings] - [HDMI
Settings] - [HDMI Signal Format] to
[Standard format] (page 19).
[Standard format] (page 19).
The surround effect cannot be
obtained.
obtained.
Depending on the input signal and
the sound field setting, surround
sound processing may not work
effectively. The surround effect may
be subtle, depending on the program
or disc.
sound processing may not work
effectively. The surround effect may
be subtle, depending on the program
or disc.
To play multi-channel audio, check
the digital audio output setting on
the device connected to the system.
For details, refer to the operating
instructions supplied with the
connected device.
the device connected to the system.
For details, refer to the operating
instructions supplied with the
connected device.
When [Audio Output] is set to
[Speaker + HDMI], the sound output
from the system’s speaker is in the
same stereo as the TV, even when
playing back multi-channel source. In
this case, set it to [Speaker] (page 55).
from the system’s speaker is in the
same stereo as the TV, even when
playing back multi-channel source. In
this case, set it to [Speaker] (page 55).
The sound is delayed behind the
picture when using the wireless
multi room function.
picture when using the wireless
multi room function.
When the sound of the [TV], [HDMI1],
[HDMI2], [HDMI3], or [Analog] input is
played in the wireless multi room
function, the sound is delayed behind
the picture. If you are bothered by a
time gap between the sound and
picture, cancel the wireless multi
room function.
played in the wireless multi room
function, the sound is delayed behind
the picture. If you are bothered by a
time gap between the sound and
picture, cancel the wireless multi
room function.
No sound or only very low-level
sound is heard from the subwoofer.
sound is heard from the subwoofer.
Press SW + on the remote control
to increase the subwoofer volume
(page 31).
(page 31).
Make sure that the on/standby
indicator on the subwoofer is lit in
green or orange.
green or orange.
If the on/standby indicator on the
subwoofer does not light, try the
following.
– Make sure the AC power cord
following.
– Make sure the AC power cord
(mains lead) of the subwoofer is
connected properly.
connected properly.
– Press
/ (on/standby) of the
subwoofer to turn on the power.
If the on/standby indicator on the
subwoofer flashes slowly in green or
orange, or lights in red, try the
following.
– Move the subwoofer to a location
orange, or lights in red, try the
following.
– Move the subwoofer to a location
near the main unit so that the on/
standby indicator on the subwoofer
lights in green or orange.
standby indicator on the subwoofer
lights in green or orange.
– Follow the steps in “Performing the
The on/standby indicator on the
subwoofer flashes quickly in green.
– Consult your nearest Sony dealer.
– Consult your nearest Sony dealer.
If the on/standby indicator on the
subwoofer flashes in red, press
/
(on/standby) of the subwoofer to
turn off the power and check whether
the ventilation holes of the
subwoofer is blocked or not.
turn off the power and check whether
the ventilation holes of the
subwoofer is blocked or not.
The subwoofer is for reproducing
bass sound. In the case of input
sources that contain very little bass
sound components (i.e., a TV
broadcast), the sound from the
subwoofer may be difficult to hear.
sources that contain very little bass
sound components (i.e., a TV
broadcast), the sound from the
subwoofer may be difficult to hear.
Set the night mode to [Off]. For
details, see “Enjoying Clear Sound
Subwoofer