President Industry Development Co. Ltd. 89390 Manuale Utente

WATCH
RECORD
REVIEW
TIMER
DELETE

Night Vision

OFF

 

/

 

ON

Video Screen

Note: Reception is good in open areas such as arenas, or outdoors on level ground and 
away from buildings and transmission towers, poles and wires. Keep a good distance away 
from home or business Wi-Fi routers. Keep away from machine rooms.

EyeSpy wireless transmission can suffer from interference caused by other 2.4MHz devices 
such as baby monitors, home wireless CCTV security systems and wireless telephones. 
Keep away from high voltage cable and towers. Keep away from communication/mobile 
stations. 
Do not use the units in damp, wet or high temperature conditions.

WATCH – When you press the button with the check mark, the screen will show you what 
the EyeSpy Eagle Eye camera is seeing. If you are in low-light conditions and the image is 
not clear, you can press the small square button on top of the viewer. This will turn on the 
amplified Night Vision circuit which will make the image easier to see, and will impart a slight 
green tint to the image. 

To take a picture, push the button with the icon of a camera on it. Note: To use this feature 
you must have an SD memory card inserted in the viewer, and the switch on the bottom of 
the Eagle Eye slid to the left.

RECORD – Note: To use this feature you must have an SD memory card inserted into the 
card socket located on the left side of the viewer, as shown in the illustration. 

 

Viewer – Slide the power switch on top of the viewer to the left. The screen will light up and 

show the EyeSpy logo. In another second or two the menu will appear as below. To 

navigate the menu there are four buttons on the front of the viewer.

 Photo - to take a picture

or start a recording

 Next - moves the screen

cursor down to choose

another task

 Select - to confirm

chosen function

 Back - cancels current

function & goes back

one step to previous function

•  You should

 

read these safety instructions and warnings before using or charging your battery. 

•  Never disassemble the viewer or try to remove the battery.
•  While generally safe, Lithium-Polymer batteries are volatile. Failure to read and follow the below 

   instructions may result in fire, personal injury and damage to property if charged or used improperly. 
•  Lithium-Polymer battery may explode and cause fire if misused or defective. 
•  When charging the battery, please place it on a fire resistant surface. Do not leave the viewer on 

   a wood surface or on paper, carpet, or grass. Do not leave the unit unattended while it is 

   charging. If at any time you witness the viewer starting to swell up, emit smoke or feel hot, 

   discontinue charging process immediately, disconnect the viewer and observe it in a safe place 

   for approximately 15 minutes. The battery may be leaking, and the reaction with air may cause 

   the chemicals to ignite, resulting in fire. In the unlikely event of this occurring, please contact us 

   via the EyeSpy website 

www.eyespytoys.com or call our Customer Assistance Line at 1866 469 9686.

•  Never store or charge the viewer inside your car in extremely warm temperatures (105ºF or 41ºC), 

   since extreme temperature could ignite a fire.
•  Never drop the viewer, as this may cause a battery to leak.

Eagle Spy:
The helicopter is equipped with a Lithium-Polymer battery that is charged with the included 
AC wall-plug adapter/charger. To charge the helicopter battery, please do the following:
A – Ensure that the black slide switch on the bottom 
of the helicopter is in the OFF position.
B – Separate the two red connectors by gently, yet 
firmly pulling the two red connectors apart.
C – Plug the white connector on the bottom of the 
helicopter into the connector at the end of the AC 
adapter/charger.
D - Plug the AC adapter/charger into a 110V AC wall 
plug and let the battery charge for three hours.
E - After charging, unplug the AC adapter from the 
wall plug and disconnect from the Eagle Spy.
F - Reconnect the battery. 

To charge

To Fly

Viewer:
The viewer’s built-in Lithium Polymer rechargeable 800mAh, 3.7 V, 
non-removable battery requires charging before its first use. The 
small plug on the included USB cord must be carefully inserted into 
the jack on the right-side of the viewer. The larger plug is inserted 
into an open USB port, found on most desktop, laptop, and 
notebook computers.
Leave the USB cord attached for three hours. After three hours, 
disconnect the USB cord. The circular opening next to the USB 
connection jack is a 1/8” mini-jack.

 

The viewer attaches to the top of the 
remote controller as shown in the diagram. 
For two person play, the screen can be 
detatched for one person to hold control 
the Eagle Spy and one person to hold the 
viewer.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to 
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.