Alarm.com 143XCVR100 Manuale Utente

The Model 2GIG-XCVR3-GC3 Transceiver Adapter is designed to be used 
with the 2GIG GC3 Security & Automation panel. The Transceiver Adapter 
is a single frequency device. It receives and transmits 900MHz signals to and 
from the Alarm.com Image Sensor (

2GIG-IMAGE2-GC3).

To use an Alarm.com Image Sensor with the GC3 panel, the Transceiver 
Adapter must be wired into the control panel.

The 2GIG GC3 panel 

must be running firmware version 3.0.1 or later to 

function with the Transceiver Adapter. To check the current version number 
of the firmware, go to the home screen of the GC3 panel and navigate to 
System Info and Usage > System Info.
If the GC3 panel is running a firmware version earlier than 3.0.1, you 
should contact Technical Support for assistance in performing an over-the-
air or local firmware upgrade. 

1.  Disconnect Power (Do Not Proceed Until this Step is Complete)

a.  Unplug the AC power supply. 
b.  Remove the back cover from the control panel and disconnect  

the backup battery cable. 

Red: Smoke +      Black: Common (GND)      Green: RX      White: TX

SKU: 2GIG-XCVR3-GC3 
900 MHz Transceiver Adapter

Transceiver Adapter for the 

Alarm.com Image Sensor

Insert the Transceiver Adapter into the wall or as far away from the GC3 
panel as possible. This ensures optimum signal strength. 

Make sure the cell radio is fully inserted into the cell slot and the cell door 
is securely closed.

a.  After the Transceiver Adapter has been installed, re-connect the 

backup battery cable. 

b.  Reattach the back cover to the GC3 panel and plug in the AC  

power supply.

 
 
 
 
 
 
 
 
 

If you are unable to successfully add an Image Sensor to an Alarm.com 
customer account, follow the recommendations below and try again:

•  Ensure the GC3 panel is running the required firmware

•  Double check that the Transceiver Adapter has been wired  

correctly to the GC3 panel

This Nortek Security & Control product is warranted against defects in material and workmanship of two (2) years. This 
warranty extends only to wholesale customers who buy direct from Nortek Security & Control LLC or through Nortek 
Security & Control LLC’s normal distribution channels. Nortek Security & Control LLC does not warrant this product to 
consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are 
no obligations or liabilities on the part of Nortek Security & Control LLC for consequential damages arising out of or in 
connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, 
or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the 
warranty expires. This Nortek Security & Control LLC Warranty all other warranties expressed or implied. All products 
returned for warranty service require a Return Authorization Number (RA#). Contact Returns at 1-855-546-3351 for an 
RA# and other important details. 

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the 
equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. 
(2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit 
different from that which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 
may not cause harmful interference. (2) This device must accept any interference received, including interference that 
may cause undesired operation.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following 
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including 
interference that may cause undesired operation of the device. 

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. 
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) 
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en 
compromettre le fonctionnement.

2GIG 
Nortek Security & Control LLC 
1950 Camino Vida Roble, Suite 150 
Carlsbad, CA 92008-6517 USA

For technical support in the USA and Canada: 
Dial 85502GIG-TECH (855-244-4832) 
Email 2gigtechsupport@nortek.com 
Visit www.2GIG.com

For technical support outside of the USA and Canada: 
Contact your regional distributor 
Visit www.nortekcontrol.com for a list of distributors in your region