Origin Electronics Machinery Co. Ltd. RF-MFX600 Manuale Utente
User Manual
Specifications:
Frequency: 2.402GHz ~ 2.480GHz
Modulation: GFSK;
Operating voltage: 5V ~ 12V;
Operating Current: 160mA
Delay time: 5 ~ 10ms
Support solutions: SAFH-2; SAFH-4 (1);
Compatible transmitter type (auto-iden): FUTABA, JR, SPEKTRUM, HiTEC
Input signal type: PPM (amplitude of 50mv or 2 ~ 5V)
Operating temperature range: 0 to 40
Frequency: 2.402GHz ~ 2.480GHz
Modulation: GFSK;
Operating voltage: 5V ~ 12V;
Operating Current: 160mA
Delay time: 5 ~ 10ms
Support solutions: SAFH-2; SAFH-4 (1);
Compatible transmitter type (auto-iden): FUTABA, JR, SPEKTRUM, HiTEC
Input signal type: PPM (amplitude of 50mv or 2 ~ 5V)
Operating temperature range: 0 to 40
Attachment function: brushed ESC SW, channel transformation SW, Multi-CH function SW
and gyro sensitivity adjustment SW had built in RX.
and gyro sensitivity adjustment SW had built in RX.
Note 1:
SAFH: Smart Auto-adapt FHSS.
SAFH-2: 2 point frequency happing. Use for micro receiver.
SAFH-4: 4 point frequency happing. Use for micro & mini standard actuator receiver.
Note 2:
Multimedia channel is based on the protocol of "Mul-CH" to achieved. For simplify to connect
on receiver, mini gyro, micro servo(Mi-LSM2400) and others equipment.
Switch and VR function introduction:
BIND switch: Binding operation switch, when pressed it the green LED will be flash, when
released it the green LED will be off. When pressed and hold on 2 seconds will be become
into binding mode.
VR function: VR1 function: gyro sensitivity adjustment, only can use on the gyro which had
built-in receiver.
SAFH: Smart Auto-adapt FHSS.
SAFH-2: 2 point frequency happing. Use for micro receiver.
SAFH-4: 4 point frequency happing. Use for micro & mini standard actuator receiver.
Note 2:
Multimedia channel is based on the protocol of "Mul-CH" to achieved. For simplify to connect
on receiver, mini gyro, micro servo(Mi-LSM2400) and others equipment.
Switch and VR function introduction:
BIND switch: Binding operation switch, when pressed it the green LED will be flash, when
released it the green LED will be off. When pressed and hold on 2 seconds will be become
into binding mode.
VR function: VR1 function: gyro sensitivity adjustment, only can use on the gyro which had
built-in receiver.
SW Functions:
SW1: Turn on or off the built-in brushed ESC in the receiver. When SW1 with ON statue
SW1: Turn on or off the built-in brushed ESC in the receiver. When SW1 with ON statue
should be turn on brushed ESC in the receiver, so you can plug the brushed motor to
receiver, when the throttle stick stay in lower point 1 seconds should be disarm the
throttle cutoff locked statue; when SW1 with OFF statue should be turn off the brushed
ESC in the receiver, so you can plug the brushless motor to receiver. Please be sure to
finished the SW1 setting before turn the transmitter.
receiver, when the throttle stick stay in lower point 1 seconds should be disarm the
throttle cutoff locked statue; when SW1 with OFF statue should be turn off the brushed
ESC in the receiver, so you can plug the brushless motor to receiver. Please be sure to
finished the SW1 setting before turn the transmitter.
SW2: Setting gyro direction or exchange aileron and direction channel of the receiver. When
you used to exchange aileron and direction channel, please refer to the instructions of
Mi-LSM2400'si