Hubsung Plastics Ltd. HUSKY24G Manuale Utente
User's Guide
2.4G
HUSKY
Proton Radio Control, Inc.
PO Box 957681 Duluth GA USA 30096
Loading battery pack
tap
hook
1
2
Adaptation for Left-hander
Antenna Installation
Top V
iew
M
steering trim
throttle
trim
mode
enter / stopwatch
down / idle
up / start
+, - / dual rate
Steering wheel
Touch buttons*
Trigger
LCD
Antenna
Stopwatch
button
Battery box
Body
Control
Panel
1. Remove the 4 screws from the bottom of
control panel.
2. Separate the control panel and the body by
slowly pulling apart.
3. Rotate the control panel 180
o
degrees and
carefully reinsert the control panel into the
body. Be carefully not to bend the pin
connectors inside.
4. Reinstall the 4 screws.
Specification of Husky 2.4G, transmitter
Modulation : 2.4 GHz, FHSS
Size : 185 X 120 X 270 mm
(7.28" X 4.72" X 10.63")
Weight : 482 g (17 oz)
Power requirements : Li-ion battery pack
(DC 7.4 V, 720mAh)
Operating temperature : 0 ~ 40
o
C
Specification of Cube 3, receiver
Modulation : 2.4 GHz, FHSS
Size : 38 X 30.5 X 16.5 mm (1.5" X 1.2" X 0.65")
Weight : 14.80 g (0.52 oz)
Power requirements : DC 3.5 ~ 10.0 V
Operating temperature : 0 ~ 40
o
C
How to establish link between the transmitter and the receiver
Each transmitter has an individually assigned unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter to which it is being paired.
Once the link is made, the ID code is stored in the receiver and no further linking is necessary unless the receiver needs to be
used with another transmitter.
Linking procedure: 1. From the transmitter's [BIND] menu, choose ID LINK and press Enter. 2. Power the Cube receiver and press the bind button (red LED above the slots) until the
LED changes to blue. 3. Confirm the link establishment by watching for servo movement when steering or triggering.
* Touch button
: The control buttons are touch sensors and they only
require a light finger touch to operate.
Important Note: To
avoid an unintended operation, touch sensor buttons are
automatically deactivated and go into hold mode after 10 seconds of
inactivity.
To reactivate the touch sensor buttons, simply rotate the steering
wheel to left or right.
Caution: Do not over tighten the antenna. Once
installed, leave it installed. Repeated removal
and reinstall can loosen the antenna base and
damage the connections, causing reduced range
and/or loss of signal.
- Charging
Use the charger included in this product. With
the battery installed in HUSKY 2.4G, plug the
charger into the charging port on the side.
Charging takes approximately 2 hours.
Rear View
USB port
power LED
power switch
charging port
Li-ion Battery Installation and Charging
1. Lightly press the hook and pull up the tap to
open the cover.
2. Place the Li-ion battery pack (NB-2LH) in the
bottom and slide towards the front so that the
battery pack is tightly sit.
3. Close the cover.
Steering servo slot
Throttle servo slot
AUX & Power slot
Bind button
Cube 3, Antenna-less Receiver
Approval
-
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device
may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsiblefor compliance could void the
authority to operate equipment.
The antenna(s) used for thistransmitter must not be co-located or operating inconjunction with any otherantenna or
t
may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsiblefor compliance could void the
authority to operate equipment.
The antenna(s) used for thistransmitter must not be co-located or operating inconjunction with any otherantenna or
t
ransmitter.
- Federal Communication Commission (FCC) Radiation Exposure Statement
For Husky 2.4G, transmitter : FCC ID RE6HUSKY24G
The remote device is approved as hand-held and hand-operation only portable (relative to hand)
device which is normally operated at 5 cm from a person's body
For Cube 3, receiver : FCC ID RE6CUBE24G3
The device and the antenna for this device must be installed to ensure a minimum separation
distance of 20 cm or more from a person's body. Other operating configurations should be avoided.
-
CE
Hereby, Hubsung Plastics Ltd. declares that this 2.4 GHz radio control system is in comd and
compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
The R&TTE (Radio Equipment & Telecommunications Terminal Equipment) directive is the new
European directive relating to radio equipment and telecommunications transmission equipment. It
also covers the collective recognition of the conformity of such equipment. One part of the R&TTE
directive regulates the introduction and operation of radio systems in the European Community. An
important change is the abolition of approval. The manufacturer or importer must subject radio
equipment to a conformity appraisal process before that equipment is introduced. The CE symbol is
attached to the device to indicate that it conforms with the valid European norms.
An exclamation mark is also to be attached to radio transmitting equipment, to indicate that the
permissible frequencies are not yet uniform throughout Europe. This requirement applies to all the
countries included in the list attached. It is essential to note that these radio control systems may
only be operated on the approved frequencies, as listed in the table.
Please note that the user bears the responsibility for compliance with this requirement, and for
ensuring that the radio system complies with the directives. In Germany the requirement to purchase
a license for the operation of 2.4 GHz systems remains in effect; please refer to the operating
instructions, or the separate sheet included with them.