Tonika Electronics Technology Co. Ltd. B020548 Manuale Utente

1. button

2. button

3. VOL(Volume) - button

4. VOL(Volume) + button

5. (Skip Backward) button

6. (Skip Forward) button

1. POWER ON/OFF switch

2. button

3. VOL (Volume) + button

4. VOL (Volume) - button

5. USB port (For DC IN)

6. LINE IN jack

AC/USB Adaptor

In fist time use, slide the insulation film from the battery door and discard it as the figure on right:

Approx.12 feet

Pairing:

DC 5V, 1.5A Through MINI USB Port

Maximum 7.5W

The button cell was consumed, replace by new one.

USB adapter

Connection Cable

Connection cable (For Charging Only)

1.5A,)

0.4A;

(Included, Already installed)

Craig warrants this product to be free from manufacturing defects in material and

workmanship under normal use for a period of 90 days from date of purchase. If service

is required, please return the product to the store where it was purchased for exchange;

or, pack the unit in the original packing material with all accessories if applicable, a copy

of your sales receipt and a Cashier’s check or Money Order for $7.00 (to cover shipping

and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please

make sure that the cashier check or money order is redeemable through a U.S. bank.

Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can

not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt

of your unit. Please ship your unit to:

Craig Electronics Inc.

1160 NW 163 Drive

Miami, Fl 33169

This warranty is void if the product has been: a) Used in a commercial application or

rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by

anyone other than an authorized Craig service center. d) Damaged because it is

improperly connected to any other equipment.

Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s

Manual which can be performed by the customer. b) Damage to equipment not properly

connected to the product. c) Any cost incurred in shipping the product for repair. d)

Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original purchase. Any implied

warranties, including the warranty of merchantability, are limited in duration to the period

of this expressed warranty and no warranty whether expressed or implied shall apply to

the product thereafter.

Under no circumstance shall Craig be liable for any loss or consequential damage arising

out of the use of this product. This warranty gives specific legal rights. However, you may

have other rights which may vary from state to state. Some states do not allow limitations

on implied warranties or exclusion of consequential damage. Therefore, these

restrictions may not apply to you.

To Obtain Service on your Product

email:service@craigelectronics.com

Printed in China

CHT913_WC_E0FG1_B0US

LIMITED WARRANTY

1. Connect the Headphone/Earphone; AUX out; Line out jacks

from the external audio player (such like MP3 player;

Discman . . . etc) to the LINE IN jacks on the unit by the

supplied Line In connection cable as the figure on right :

2. Slide the POWER ON/OFF Switch of the unit to ON

position to power on the unit. The STANDBY Indicator

will turn on.

3. Press the button on the unit or Remote Control to turn

the unit ON from standby mode. The STANDBY indicator

will blink. Press again to turn to STANDBY mode.

Note: If unplug the Line In Connection Cable from the Line

In Jack. The unit will turn to BT mode automatically

and the color of STANDBY Indicator will turn to blue.

4. Press the VOL +/- buttons to adjust volume levels (When

the volume level turned to maximum or minimum, two shot

tones will be heard from speaker).

5. Press the button on the Remote Control to mute the

sound temporary, press again to resume.

6. When finished listening, press the button to turn off

(standby mode) the unit.

NOTE: To saving the electric power, unplug the AC/USB Adaptor from wall outlet if

long period of time will not use.

1. Make sure the Line In Connection Cable is Unplug from the LINE IN jack.

2. Slide the POWER ON/OFF Switch of the unit to ON position to power on the unit. The STANDBY

Indicator will turn on.

3. Press the button on the unit or Remote Control to turn the unit ON from standby mode. The BT

Indicator (Blue) will light and blink.

Notes:

~ When the external BT Device searched the unit, our model number “CHT 913” will appear on

the display of external BT Device.

~ Pairing code “0000” may need to enter.

Normal operation after paired:

1. Turn on the BT function of the external BT Device.

2. Power on the unit and enter to BT mode as previous procedures.

3. Wait a few seconds unit the unit paired to the external BT Device automatically. (The BT Indicator

will stop blinking).

4. Plays the music in the connected BT Device as usual.

5. During playback:

~ Press the button on the Remote Control to pause; press again to resume normal playback.

~ Press and release the VOL +/- buttons on the unit or / buttons on the Remote Control to

skip tracks.

~ Press and hold the VOL +/- buttons on the unit or press the VOL +/- buttons on the Remote

Control to adjust volume level. (When the volume level turned to maximum or minimum, two

shot tones will be heard from speaker).

Follow these precautions when using a battery in this device:

1. Use only the size and type of battery specified.

2. Be sure to follow the correct polarity when installing the battery as indicated in the battery

compartment A reversed battery may cause damage to the device.

3. If the battery in the device is consumed or the device is not to be used for a long period of time.

remove the batteries to prevent damage or injury from possible battery leakage.

4. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture

5. The batteries shall not be exposed to excessive heat such as sunshine. fire or the like

6. Clean the battery contacts and also those of the device prior to battery installation

7. Do not mix different types of batteries together (e.g Alkaline and Carbon-zinc) or old batteries

with fresh ones

8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed. it

can cause severe internal burn in just 2 hours and can lead to death Keep new and used

batteries away from children. If the battery compartment does not close securely. stop using

the product and keep it away from children. If you think batteries might have been swallowed

or placed inside any parl of the body. seek immediate medical attention

BATTERY PRECAUTIONS

NOTES:
● When there is an obstacle between the unit and the
transmitter, the transmitter may not operate.
● When direct sunlight, an incandescent lamp,
fluorescent lamp or any other strong light shines on
the REMOTE SENSOR of the unit, the remote
operation may be unstable.

1. Insert the small plug from the supplied USB

Connection cable to the Mini USB Pod on

the Right of unit.

2. Insert the big plug from the supplied USB

Connection cable to the USB Port on the

supplied AC/USB Adaptor

3. Insert the AC/USB Adaptor to wall outlet

having AC 100-240V~ , 50/60Hz.

NOTE: This AC/USB Adaptor is intended to be correctly orientated in a vertical or

floor mount position.