Long-E Technology Co. Ltd. TA31TA37 Manuale Utente
GS-500A W/O ANTI HIJACKING FUNCTIONAL MANUAL Page 2 of 5
arming). The parking lights will flash. The doors will lock.
**
The status LED will begin flashing.
4) The system is now armed.
*
The ignition must have been on for at least
3
seconds or the Passive Arming sequence will be disabled.
**
If the passive locking feature is selected.
To temporarily disable Passive Arming, turn on the ignition then turn off within
3
seconds. The siren will chip once indicating
the system will not passively arm until the ignition is cycled again.
If the Passive Arming with Countdown feature is programmed, the siren will chirp every 2 seconds until the system passively
arms.
arms.
Note: If the Passive Arming feature is enabled, the Automatic Rearming feature will also be enabled even if it was not
already programmed.
already programmed.
7. PANIC MODE
In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm.
To activate the Panic Mode:
1) When ACC off, press and hold Button 1 for 2 seconds. The alarm will sound for 30 seconds. The parking lights will flash.
In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm.
To activate the Panic Mode:
1) When ACC off, press and hold Button 1 for 2 seconds. The alarm will sound for 30 seconds. The parking lights will flash.
The doors will lock then unlock
*
allowing access to the vehicle.
2) Press Button 2 to stop Panic Mode.
*
If the ignition is on when the panic feature is activated, the doors will lock for personal safety.
8. EMERGENCY OVERRIDE
If the transmitter becomes lost or inoperable, the system can still be disarmed using the following procedure. Before beginning
this procedure be sure to have the ignition key ready and know the location of the override switch.
To Emergency Override the system:
1) Unlock the door using the key.
2) Enter the vehicle. The system will trigger and the siren will sound.
3) Turn ignition key on.
4) Press and hold the override switch for 5 seconds. The system will disarm.
5) The vehicle will now be able to start.
9. Optional Coded Emergency Override
As an extra measure of security, the system is equipped with an optional Coded Emergency Override feature. Once an
Emergency Override Coded is chosen and programmed during installation, the system can no longer be disarmed using the
standard Override procedure.
To Emergency Override the system using the Code:
1) Follow steps 1-3 above.
2) Press the override switch a number of times equal to the Disarm code, and continue holding for 5 seconds on the last press.
If the transmitter becomes lost or inoperable, the system can still be disarmed using the following procedure. Before beginning
this procedure be sure to have the ignition key ready and know the location of the override switch.
To Emergency Override the system:
1) Unlock the door using the key.
2) Enter the vehicle. The system will trigger and the siren will sound.
3) Turn ignition key on.
4) Press and hold the override switch for 5 seconds. The system will disarm.
5) The vehicle will now be able to start.
9. Optional Coded Emergency Override
As an extra measure of security, the system is equipped with an optional Coded Emergency Override feature. Once an
Emergency Override Coded is chosen and programmed during installation, the system can no longer be disarmed using the
standard Override procedure.
To Emergency Override the system using the Code:
1) Follow steps 1-3 above.
2) Press the override switch a number of times equal to the Disarm code, and continue holding for 5 seconds on the last press.
the system will disarm . If the code is entered incorrectly, turn off the ignition and begin again.
To set the emergency override code:
1) Turn on ignition.
2) Within 5 seconds, press the valet switch 5 times.
1) Turn on ignition.
2) Within 5 seconds, press the valet switch 5 times.
The siren will provide one long chirp, indicating that you have entered programming.
3) Press the valet switch 3 times.
The siren will chirp each time the valet switch is pressed.
4) Within 5 seconds, press button 3 on the transmitter.
The siren will chirp 3 times.
5) Press the valet switch the number of time equal to the desired code(from 1-15). If there is no press on the valet switch at this
stage but turn ignition off and arm the system, then it returns to the factory default to override the system, and no code is
required any more in emergency disarming.
required any more in emergency disarming.
6) Turn off the ignition then
arm the system.
7) Disarm the system using the new override code to permanently store the new code.
NOTE: if the code set procedure is not properly performed, turn off the ignition and begin again. The override code will not be
permanently stored until the code is used to disarm the system.
10. AUTOMATIC REARMING
The automatic Rearming feature is designed to protect the vehicle in the event the system is accidentally disarmed. With the
Automatic Rearming feature enabled, the alarm will automatically rearm 30 seconds after disarming. If the optional Passive
Door lock feature is enabled, the doors will also lock when the system rearms.
The Automatic Rearming feature will be temporarily bypassed until the next arming cycle if the ignition is turned on or the
door/trunk/hood zone is opened.
11. VALET MODE
The valet mode temporarily disables the security system so the vehicle may be operated by a mechanic or parking attendant.
To activate or deactivate the valet mode:
1) Turn on the ignition.
2) Press and hold the override switch for 5 seconds.
NOTE: if the code set procedure is not properly performed, turn off the ignition and begin again. The override code will not be
permanently stored until the code is used to disarm the system.
10. AUTOMATIC REARMING
The automatic Rearming feature is designed to protect the vehicle in the event the system is accidentally disarmed. With the
Automatic Rearming feature enabled, the alarm will automatically rearm 30 seconds after disarming. If the optional Passive
Door lock feature is enabled, the doors will also lock when the system rearms.
The Automatic Rearming feature will be temporarily bypassed until the next arming cycle if the ignition is turned on or the
door/trunk/hood zone is opened.
11. VALET MODE
The valet mode temporarily disables the security system so the vehicle may be operated by a mechanic or parking attendant.
To activate or deactivate the valet mode:
1) Turn on the ignition.
2) Press and hold the override switch for 5 seconds.
The siren will chirp once to confirm the valet mode is on.
The siren will chirp twice to confirm the valet mode is off.
3) Turn off the ignition.
While in valet mode the remote transmitters will continue to lock and unlock the doors, and operate the optional auxiliary
functions.
12. IGNITION CONTROLLED DOOR LOCKS
For added safety, the Ignition Door locking feature. Allows vehicles equipped with power door lock systems to automatically
lock the doors when the ignition is turned on. When igntion off, the door lock shall unlock automatically. The ignition locking
feature is disabled to protect against locking the keys inside the vehicle. See function selection #4.
13. DOME LIGHT ACTIVATION
If the optional Dome light Activation feature is installed, the dome light will turn on when the system is disarmed using the
Remote Transmitter. The dome light will remain on for 30 seconds or until the ignition is turned on.
14. AUXILIARY FUNCTION OUTPUTS
The system is equipped with 2 Auxiliary Outputs allowing the convenience features of the system to be further expanded. These
outputs can be used to add a number of optional features such as: power trunk release, remote engine start, power window
activation, power sunroof control, and more.
15. REMOTE SENSOR DISABLE
When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong weather conditions that could
cause the sensors to trigger, the sensor inputs can be temporarily bypassed using the Remote Transmitter, preventing possible
false alarms.
To disable the sensor inputs:
1) Arm the system normally.
2) Within 5 seconds of Arming the system, press the Arm button again. The siren will chirp 5 times and the parking lights will
12. IGNITION CONTROLLED DOOR LOCKS
For added safety, the Ignition Door locking feature. Allows vehicles equipped with power door lock systems to automatically
lock the doors when the ignition is turned on. When igntion off, the door lock shall unlock automatically. The ignition locking
feature is disabled to protect against locking the keys inside the vehicle. See function selection #4.
13. DOME LIGHT ACTIVATION
If the optional Dome light Activation feature is installed, the dome light will turn on when the system is disarmed using the
Remote Transmitter. The dome light will remain on for 30 seconds or until the ignition is turned on.
14. AUXILIARY FUNCTION OUTPUTS
The system is equipped with 2 Auxiliary Outputs allowing the convenience features of the system to be further expanded. These
outputs can be used to add a number of optional features such as: power trunk release, remote engine start, power window
activation, power sunroof control, and more.
15. REMOTE SENSOR DISABLE
When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong weather conditions that could
cause the sensors to trigger, the sensor inputs can be temporarily bypassed using the Remote Transmitter, preventing possible
false alarms.
To disable the sensor inputs:
1) Arm the system normally.
2) Within 5 seconds of Arming the system, press the Arm button again. The siren will chirp 5 times and the parking lights will
flash 5 times to indicate the sensors are disabled. The sensors will remain disabled until the next arming cycle.
16. Entering System Programming
To enter System Programming:
3) Turn on ignition.
4) Within 5 seconds, press the valet switch 5 times.
To enter System Programming:
3) Turn on ignition.
4) Within 5 seconds, press the valet switch 5 times.
The siren will provide one long chirp, indicating that you have entered Programming.
5) Press the valet switch the number times equal to the System Option you want to change.
The siren will chirp each time the valet switch is pressed.
6) Within 5 seconds, press the transmitter button corresponding to the desired operating mode for that System Option.
The siren will chirp to indicate the setting.
1 chirp = Button 1
2 chirps = Button 2
3 chirps = Button 3
7) When you are finished, turn off the ignition to save the changes.
17. Default Reset
Following this procedure will set all Programmable System Options to factory default settings.
1) Enter System programming.
2) press Transmitter Button 3.
The siren will chirp 4 times indicating that the reset signal was received.
2 chirps = Button 2
3 chirps = Button 3
7) When you are finished, turn off the ignition to save the changes.
17. Default Reset
Following this procedure will set all Programmable System Options to factory default settings.
1) Enter System programming.
2) press Transmitter Button 3.
The siren will chirp 4 times indicating that the reset signal was received.
All programmable System Options are now set to factory default settings.
The Valet Mode is off.
The Disarm Code is 1.
The Valet Mode is off.
The Disarm Code is 1.
3) Turn off ignition.
PROGRAMMABLE SYSTEM OPTIONS
Branch Feature
Button1(default)
Button2
Button3
1.Horn Chirps W/ Arm&Disarm
Normal
Horn Chirps
Horn Chirps w/warn
2.Arm Mode
Manual Arming
Passive Arming
Passive w/Countdown
3.Passive Door Locking
Disabled
Enabled
Set Override Code
4.Ignition Controlled Locks
On
Off
Lock Only
5. Channel 2 mode
0.5s pulse
10s
latched
6. Channel 3 mode
0.5s pulse
10s
latched
7. Door lock Pulse Length
1 Second
3 seconds
0.1 second
10.Ignition Armed Mode
Disabled
Enabled
11.Door Input Monitoring
5 Seconds
10 Seconds
60 Seconds
12.Auto Rearming
Disabled
Enabled
13.Door Unlock Pulse
Single
Double
14.Arming Chirps
Normal
Silent
15.Extended Parking Lights
Off
On
16.Disarm Chirp
Normal
Silent