Impinj Inc. XARRAY Manuale Utente
Speedway Revolution Installation and Operations Guide Octane 4.11
Chapter 1: Introduction
Chapter 1: Introduction
6
Revision 4.11 Copyright ©2014, Impinj, Inc.
• Connecting to the Reader console port requires a Cisco type management cable (RJ-
45 to DB9) and either a RS-232 serial port or serial to USB adapter on the PC.
• Impinj-approved UHF RFID antenna or antennas, including associated RF cable or
cables with RP-TNC male connector interface.
Power Requirements
Warning:
This product is intended to be
supplied with a Listed/Certified power
supply, marked LPS or Class 2, with 24Vdc
output, rated minimum 2.5A. Use of
alternative power supply will invalidate any
approval given to this device and may be
dangerous.
supply, marked LPS or Class 2, with 24Vdc
output, rated minimum 2.5A. Use of
alternative power supply will invalidate any
approval given to this device and may be
dangerous.
Avertissement
: Ce produit est conçu
pour être alimenté avec une alimentation Mis
/ certifiés, marqué LPS ou de classe 2, avec
sortie 24V, 2,5 A nominal minimum.
Utilisation d'une autre alimentation annule
toute autorisation liée à cet appareil et peut
être dangereuse.
/ certifiés, marqué LPS ou de classe 2, avec
sortie 24V, 2,5 A nominal minimum.
Utilisation d'une autre alimentation annule
toute autorisation liée à cet appareil et peut
être dangereuse.
When supplied from an IEEE802.3af (Power over Ethernet) compliant power source which is
certified by the appropriate agencies, the RF transmit power is limited to +30dBm. When
supplied by the Impinj approved Listed/Certified power supply model number IPJ-A2002-
000, the RF transmit power supports upto +32.5dBm. Operating above +30 dBm requires
professional installation to comply with radio regulatory laws in many countries. See
Appendix A:
certified by the appropriate agencies, the RF transmit power is limited to +30dBm. When
supplied by the Impinj approved Listed/Certified power supply model number IPJ-A2002-
000, the RF transmit power supports upto +32.5dBm. Operating above +30 dBm requires
professional installation to comply with radio regulatory laws in many countries. See
Appendix A:
on page 35 for details.
Available AC power cords for the IPJ-A2002-000 power supply are:
IPJ-A2051-USA (for North America)
IPJ-A2051-EU1 (for European Union)
IPJ-A2051-AUS (for Australia, New Zealand)
IPJ-A2051-BRA (for Brazil)
IPJ-A2051-CHN (for China)
IPJ-A2051-JPN (for Japan)
IPJ-A2051-RSA (for South Africa)
IPJ-A2051-UK1 (for UK, Singapore, Malaysia, Hong Kong)
Supported Operating Environments
This section describes the environments in which you can access the Speedway Revolution
RShell console used for configuring, monitoring, and maintaining the Reader. The tools you
use when accessing the RShell console depend on how you connect your PC to the Reader:
serial connection (RS-232) or Ethernet connection (SSH/Telnet). On PCs running Microsoft
Windows, you can now use Putty for both types of connections.
RShell console used for configuring, monitoring, and maintaining the Reader. The tools you
use when accessing the RShell console depend on how you connect your PC to the Reader:
serial connection (RS-232) or Ethernet connection (SSH/Telnet). On PCs running Microsoft
Windows, you can now use Putty for both types of connections.
Table 1.1: Supported Operating Environments
Interface
Protocol
Recommended Tools
Microsoft Windows
Linux
Ethernet
SSH-Port 22
Telnet-Port 23
Putty
1
SSH or Telnet
Serial
RS-232
Putty (version 0.60 and
higher supports serial)
Minicom
1.
http://www.chiark.greenend.org.uk/~sgtatham/putty/