King Sound Enterprise Co. Ltd KINGSOUNDST1 Manuale Utente
1
OUTDOOR SUPER SWITCH （KSI-393/293/194）
Wireless Remote Control Wall Outlets
Set of 3 Outdoor Outlets and Remote
Package Includes:
(3) Wireless Wall Outlet Receivers (Receiver Units)
(1) Three Button Hand-Held Remote Control (Sender Unit)
(1) Car Visor Clip
(1) 12V Type 23A battery
(1) Three Button Hand-Held Remote Control (Sender Unit)
(1) Car Visor Clip
(1) 12V Type 23A battery
Features:
The Super Switch operates on radio frequency and is not dependent on line of sight and will perform
through walls, doors and floors up to 60 feet away. No rewiring is required. Car visor clip included for
convenience.
through walls, doors and floors up to 60 feet away. No rewiring is required. Car visor clip included for
convenience.
Operation:
Remove Tape From Battery Chamber.
Remove battery cover on Hand-Held Remote Control unit and remove protective tape. Re-install battery
cover.
Plug in Outdoor Receiver Units.
Plug the individual wall receiver units into any standard grounded outdoor 115V/60Hz wall outlet.
Remember, the outdoor receiver requires a grounded outlet. If you do not have an outdoor grounded
outlet, you should contact an electrician to upgrade your electrical system for your safety.
Mount Outdoor Receiver Units.
Hang outdoor receiver with nails or screws. There is a keyhole on the back of the receiver for this
purpose. DO NOT allow outdoor receiver to hang loose by cord. The outdoor receiver MUST be oriented
with the power outlet down to prevent rain from entering the unit. The outdoor receiver must be located
below the wall outlet to prevent rain from running down the cord into the wall outlet. DO NOT position the
outdoor receiver flat on the ground because the outdoor receiver is NOT water proof or submersible.
Note: The National Electrical Code and Canadian Electrical Code require that outside outlets be protected
by a Ground Fault Interrupter (GFI).
Operation and Safety.
Use only 1 Super Switch Receiver per outdoor AC outlet. A distance of 24 inches should be maintained
between individual receiver units. Do not overload individual Super Switch receiver units beyond 920
watts. Maximum output load: 115V/60Hz/8A. The outdoor receiver is water resistant, NOT water proof or
submersible. Therefore, reasonable care should be taken to insure the outdoor receiver is correctly
mounted or positioned according to the above instructions.
Outdoor Receiver Function.
The Red LED (ON) will illuminate when outdoor receiver power is ON. If the Red LED (ON) does not
illuminate check to be sure your outdoor wall outlet is powered ON.
Remove battery cover on Hand-Held Remote Control unit and remove protective tape. Re-install battery
cover.
Plug in Outdoor Receiver Units.
Plug the individual wall receiver units into any standard grounded outdoor 115V/60Hz wall outlet.
Remember, the outdoor receiver requires a grounded outlet. If you do not have an outdoor grounded
outlet, you should contact an electrician to upgrade your electrical system for your safety.
Mount Outdoor Receiver Units.
Hang outdoor receiver with nails or screws. There is a keyhole on the back of the receiver for this
purpose. DO NOT allow outdoor receiver to hang loose by cord. The outdoor receiver MUST be oriented
with the power outlet down to prevent rain from entering the unit. The outdoor receiver must be located
below the wall outlet to prevent rain from running down the cord into the wall outlet. DO NOT position the
outdoor receiver flat on the ground because the outdoor receiver is NOT water proof or submersible.
Note: The National Electrical Code and Canadian Electrical Code require that outside outlets be protected
by a Ground Fault Interrupter (GFI).
Operation and Safety.
Use only 1 Super Switch Receiver per outdoor AC outlet. A distance of 24 inches should be maintained
between individual receiver units. Do not overload individual Super Switch receiver units beyond 920
watts. Maximum output load: 115V/60Hz/8A. The outdoor receiver is water resistant, NOT water proof or
submersible. Therefore, reasonable care should be taken to insure the outdoor receiver is correctly
mounted or positioned according to the above instructions.
Outdoor Receiver Function.
The Red LED (ON) will illuminate when outdoor receiver power is ON. If the Red LED (ON) does not
illuminate check to be sure your outdoor wall outlet is powered ON.