RadioFrame Networks Inc MCSERIES10 Manuale Utente

MC-Series System Installation & Testing 

RadioFrame Networks, Inc.

 

DAT_6 

111-0001-02 

BIC:  CRTC 10base2 - ISC 

ISC 1:  10B2-1 

COAX 

CLK_1 

111-0001-02 

BIC:  ERTM 5MHz/1PPS IN 

ISC 1:  SITE REF OUT 1 

COAX 

* Remove both ends of this cable and keep it for the replacement BIC. 

For the AIC, disconnect the following cabling from the rear of the AIC only: 

P_12 

820-0614-10 

AIC:  power 

PDU:  AIC 

power 

G_13 

820-0609-00 

AIC:  ground 

GND BAR 

ground 

DAT_1 

111-0566-00 

AIC:  ERTM PORT 1 

RBS 1:  10/100 RFN A 

UTP 

DAT_2 

111-0566-00 

AIC:  ERTM PORT 2 

RBS 1:  10/100 RFN B 

UTP 

DAT_3 

111-0566-00 

AIC:  ERTM PORT 3 

RBS 1:  10/100 RFN C 

UTP 

DAT_5 

111-0565-00 

AIC:  ERTM PORT 4 

BIC:  ERTM PORT 2 

UTP 

 

For the RBS 1, disconnect the following cabling from the rear of the RBS 1 only: 

NOTE:  If RBS 2 and RBS 3 are present, refer to the cabling diagrams in Appendix C for 
corresponding cabling indexes. 

P_6 

820-0616-50 

RBS 1:  power 

PDU:  RBS 1 

power 

G_8 

820-0609-00 

RBS 1:  ground 

GND BAR 

ground 

RF_1 

820-0611-20 

RBS 1:  Tx A 

RF Shelf 1:  Tx IN A  

RF cable

 

RF_4 

820-0611-20 

RBS 1:  Rx A 

RF Shelf 1:  Rx OUT A  

RF cable

 

AL_1 

820-0607-00 

RBS:  ALARM INPUT A 

RF Shelf 1:  ALARM 

serial 

DAT_1 

111-0566-00 

RBS 1:  10/100 RFN A 

AIC:  ERTM PORT 1 

UTP 

RF_2 

820-0611-20 

RBS 1:  Tx B 

RF Shelf 2:  Tx IN B  

RF cable

 

RF_5 

820-0611-20 

RBS 1:  Rx B 

RF Shelf 2:  Rx OUT B  

RF cable

 

AL_2 

820-0607-00 

RBS:  ALARM INPUT B 

RF Shelf 2:  ALARM 

serial 

DAT_2 

111-0566-00 

RBS 1:  10/100 RFN B 

AIC:  ERTM PORT 2 

UTP 

RF_3 

820-0611-20 

RBS 1:  Tx C 

RF Shelf 3:  Tx IN C  

RF cable

 

RF_6 

820-0611-20 

RBS 1:  Rx C 

RF Shelf 3:  Rx OUT C  

RF cable

 

AL_3 

820-0607-00 

RBS:  ALARM INPUT C 

RF Shelf 3:  ALARM 

serial 

DAT_3 

111-0566-00 

RBS 1:  10/100 RFN C 

AIC:  ERTM PORT 3 

UTP 

 

Remove the chassis from the rack, and package it for shipment.  

Mount the replacement chassis.  

While supporting the chassis, slide the chassis into the cabinet mounting position. Secure the 
chassis to the cabinet mounting rails using the four mounting screws provided with the unit. 
Tighten the screws to 4.5 Nm (40 in-lb).  

Reconnect the cabling to the replacement chassis as defined in Step 2.  

Use the SMA torque wrench for all SMA connectors. 

Using the breakers on the PDU, turn up the BIC, AIC, and RBS 1 (and RBS 2 and RBS 3 if 
present), and then verify that the components are operational before proceeding.