Hafele America Co. 103 Manuale Utente
P
ROGRAMMING
S
TATION
(PUPC1)
I
NSTALLATION
M
ANUAL
Häfele America
NOTICE: Any changes or modifications made to the
PUPC1 will void the user’s authority to operate this
equipment in compliance with FCC regulations.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures: Reorient or
relocate the receiving antenna. Increase the separation
between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the factory
or an experienced radio/TV technician for help.
PUPC1 will void the user’s authority to operate this
equipment in compliance with FCC regulations.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures: Reorient or
relocate the receiving antenna. Increase the separation
between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the factory
or an experienced radio/TV technician for help.
1.
Introduction
The Programming Unit IR PC allows a PC
workstation to program user keys and to
exchange data with hand-held program-
mers.
workstation to program user keys and to
exchange data with hand-held program-
mers.
The PUPC1 is equipped with a Reader
that can communicate with proximity keys
placed at its apex. It also has an IR port
that can communicate bi-directionally with
such devices as the handheld BCL.
that can communicate with proximity keys
placed at its apex. It also has an IR port
that can communicate bi-directionally with
such devices as the handheld BCL.
Figure 1: The PUPC1 Programming Unit
The PC Programming Unit is connected
through a standard DB9 RS232 serial ca-
ble to the COM port of the workstation,
and is powered through a 9VAC wall
transformer that is supplied with the unit.
through a standard DB9 RS232 serial ca-
ble to the COM port of the workstation,
and is powered through a 9VAC wall
transformer that is supplied with the unit.
The PC needs to be loaded with one of
the Dialock software programs (e.g. Per-
sonnel, Hotel).
In a typical Dialock PC-application, the
PUPC1 is used to recognize an activation
key that unlocks the programming soft-
ware. Once the software is accessed, it
allows the following functionality:
the Dialock software programs (e.g. Per-
sonnel, Hotel).
In a typical Dialock PC-application, the
PUPC1 is used to recognize an activation
key that unlocks the programming soft-
ware. Once the software is accessed, it
allows the following functionality:
• Reading
keys
• Programming R/W keys
• Downloading
• Downloading
Terminal
configuration
to a handheld Beam Control Lite
• Uploading data from the BCL (which
may include event history from a
Terminal)
Terminal)
Two LEDs are provided on the PUPC1 to
indicate its operating status.
indicate its operating status.
Ordering Information
Description Article
No.
PUPC1 without PS
910.51.511
9VAC Wall transformer
824.19.376.xx
Table 1: PUPC1 Ordering Info
2.
Installation Guide
a. Plug the DB9 9-position plug at-
tached to the PUPC1 to the
RS232C serial port of the PC
RS232C serial port of the PC
b. Connect the 3.5 mm plug from the
supplied 9VAC transformer to the
mating socket attached to the pro-
grammer’s cable.
mating socket attached to the pro-
grammer’s cable.
c. Plug the transformer to a 120VAC
wall outlet. The red LED on the
PUPC1 should turn on.
PUPC1 should turn on.
d. The PUPC1 is now ready for use.
3.
Operating Instructions
Please follow the detailed use instructions
set in the software manuals for the Com-
plete Dialock systems.
set in the software manuals for the Com-
plete Dialock systems.
File: PUPC1 Installation Manual.doc
Updated 11/7/01