AirVast Technology Inc. WN360G Manuale Utente
M060603V10
STATEMENT FOR MODUAL APPROVAL
This product is sold to OEM integrators
,
only. The manual for the OEM integrators must include some
instructions to be followed by the end users in the user manual. For example:
- The OEM integrators must be instructed to ensure that the end user has no manual instructions to remove or
install the device.
- The OEM integrators must be instructed about the end product labeling ("Contains TX FCC ID:
QDWWN360G")
etc.
Please add the following statements to the manuals for the OEM integrators:
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end product for any additional compliance requirements required
with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users (for example, access points, routers, wireless ADSL
modems, and similar equipment). The final end product must be labeled in a visible area with the following:
"Contains TX FCC ID: QDWWN360G".
Manual Information for End Users
The end user must not have manual instructions to remove or install the device.
The user manual for end users must include the following information in a prominent location.
“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or transmitter."
- The OEM integrators must be instructed to ensure that the end user has no manual instructions to remove or
install the device.
- The OEM integrators must be instructed about the end product labeling ("Contains TX FCC ID:
QDWWN360G")
etc.
Please add the following statements to the manuals for the OEM integrators:
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end product for any additional compliance requirements required
with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users (for example, access points, routers, wireless ADSL
modems, and similar equipment). The final end product must be labeled in a visible area with the following:
"Contains TX FCC ID: QDWWN360G".
Manual Information for End Users
The end user must not have manual instructions to remove or install the device.
The user manual for end users must include the following information in a prominent location.
“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or transmitter."