Interactive Toy Concepts Limited 50XXXTX49 Manuale Utente
1. Slide to open the battery
compartment door.
compartment door.
2. Insert the 1 x 9V battery according to
the picture shown. Ensure that the
+ and - polarities match the illustrations
inside the battery compartment.
the picture shown. Ensure that the
+ and - polarities match the illustrations
inside the battery compartment.
3. Replace the battery compartment door.
CHARGING THE HELICOPTER
Before flying the Helicopter for the first time or if you have depleted the charge, you will
need to recharge it. A typical charge takes about 30-60 minutes and allows for approximately 4-6 minutes
of flying time.
need to recharge it. A typical charge takes about 30-60 minutes and allows for approximately 4-6 minutes
of flying time.
MAKE SURE THE HELICOPTER IS TURNED OFF BEFORE THE RECHARGING CYCLE IS COMMENCED.
Note: During charging, both the RED LED on helicopter will light up. The LED will extinguish completely
when the charge is complete.
when the charge is complete.
1) Ensure the Helicopter is turned off. When the helicopter turn off, the front LED turned off.
2) Insert the USB charging wire into any USB power source as shown. Make sure the USB source has
power on.
3) Insert the USB charging wire into the Helicopter charging port which located on the right side of the
Helicopter.
4) The charging LED of Helicopter turn on. The Helicopter is charging. It takes 30-60 minutes to finish the
charging.
5) When the charging LED turn off, the charging is completed.
6) Gently remove the charging wire from the Helicopter.
2) Insert the USB charging wire into any USB power source as shown. Make sure the USB source has
power on.
3) Insert the USB charging wire into the Helicopter charging port which located on the right side of the
Helicopter.
4) The charging LED of Helicopter turn on. The Helicopter is charging. It takes 30-60 minutes to finish the
charging.
5) When the charging LED turn off, the charging is completed.
6) Gently remove the charging wire from the Helicopter.
ON/OFF LED
MODE SWITCH
FORWARD/BACKWARD
DIRECTIONAL CONTROL
DIRECTIONAL CONTROL
Insert the USB charging wire into
any USB power source.
any USB power source.
USB charging port
in the Helicopter.
in the Helicopter.
Insert the USB charging wire the USB
charging port in the Helicopter.
charging port in the Helicopter.
1. Turn the controller on by press the ON/OFF Button. The ON/OFF LED will light up.
2. Turn on the Helicopter on by slide ON/OFF switch located at the left side of the Helicopter as shown. The front LED will light up.
3. Place the Helicopter on a flat level surface for launch.
4. On the controller, push the left stick all the way up once, and bring it back down completely to activate the control.
5. Push the left stick up again to activate the main rotors of the Helicotper.
6. Check to make sure that the main rotors are spinning smoothly. Increase the rotational speed of the main rotors by pushing the
(throttle control) Left Stick up. The Helicopter can be launched from a horizontal surface.
7. Add more throttle by pushing up the Left Stick to increase altitude.
8. For maximum stability you may have to adjust the trim during flight as the Helicopter will likely begin to rotate in the air. Simply,
turn the Trim Knob on your controller to the left if your Helicopter is rotating to the right. Turn the Trim Knob on your controller to
the right if your Helicopter is rotating to the left.
9. To control the forward or backward move, simply slide the (Directional Control) Right Stick on the controller to Up or Down. Slide
the Right Stick to the Up to move forward, or slide the Right Stick to the Down to move backward.
10. To control the left or right turn, simply slide the (Directional Control) Right Stick on the controller to Left or Right. Slide the Right
Stick to the Left to turn left, or slide the Right Stick to the Right to turn right.
11. As the Helicopter is flying towards you, you will naturally experience a phenomenon called “Control Reversal”. Pushing the Right
Stick to the right will make the Helicopter fly to the left as it flies towards you. Pushing the Right Stick to the left will make the
Helicopter fly to the right as it flies towards you.
12. If you are ready to fly more quickly, you can change to PRO mode. Slide the Mode Switch to PRO, then the forward or backward
speed increases.
13) The Helicopter can be landed on just about any flat, stable surface. Gently release the (Throttle Control) Left Stick. The Left Stick
is spring-loaded so releasing it will cause it to go down all the way. As the Left stick is gradually released, the main rotors will
gradually slown down and stop rotating. The Helicopter will gradually land. It is important to not release the Left Stick suddenly
while the Helicopter is still in the air. Doing this will stop the Main Rotors completely and make the Helicopter fall out of the air.
14) To Recharge your Helicopter follow the steps as outlined in “CHARGING THE HELICOPTER”.
2. Turn on the Helicopter on by slide ON/OFF switch located at the left side of the Helicopter as shown. The front LED will light up.
3. Place the Helicopter on a flat level surface for launch.
4. On the controller, push the left stick all the way up once, and bring it back down completely to activate the control.
5. Push the left stick up again to activate the main rotors of the Helicotper.
6. Check to make sure that the main rotors are spinning smoothly. Increase the rotational speed of the main rotors by pushing the
(throttle control) Left Stick up. The Helicopter can be launched from a horizontal surface.
7. Add more throttle by pushing up the Left Stick to increase altitude.
8. For maximum stability you may have to adjust the trim during flight as the Helicopter will likely begin to rotate in the air. Simply,
turn the Trim Knob on your controller to the left if your Helicopter is rotating to the right. Turn the Trim Knob on your controller to
the right if your Helicopter is rotating to the left.
9. To control the forward or backward move, simply slide the (Directional Control) Right Stick on the controller to Up or Down. Slide
the Right Stick to the Up to move forward, or slide the Right Stick to the Down to move backward.
10. To control the left or right turn, simply slide the (Directional Control) Right Stick on the controller to Left or Right. Slide the Right
Stick to the Left to turn left, or slide the Right Stick to the Right to turn right.
11. As the Helicopter is flying towards you, you will naturally experience a phenomenon called “Control Reversal”. Pushing the Right
Stick to the right will make the Helicopter fly to the left as it flies towards you. Pushing the Right Stick to the left will make the
Helicopter fly to the right as it flies towards you.
12. If you are ready to fly more quickly, you can change to PRO mode. Slide the Mode Switch to PRO, then the forward or backward
speed increases.
13) The Helicopter can be landed on just about any flat, stable surface. Gently release the (Throttle Control) Left Stick. The Left Stick
is spring-loaded so releasing it will cause it to go down all the way. As the Left stick is gradually released, the main rotors will
gradually slown down and stop rotating. The Helicopter will gradually land. It is important to not release the Left Stick suddenly
while the Helicopter is still in the air. Doing this will stop the Main Rotors completely and make the Helicopter fall out of the air.
14) To Recharge your Helicopter follow the steps as outlined in “CHARGING THE HELICOPTER”.
FLYING THE HELICOPTER
NOTE: YOU WILL NEED TO RE-ACTIVATE THE CONTROLS EVERY TIME YOU SWITCH
THE HELICOPTER ON AND OFF BY SLIDING THE LEFT STICK UP AND DOWN ONCE.
THE HELICOPTER ON AND OFF BY SLIDING THE LEFT STICK UP AND DOWN ONCE.