Advanced Control Technologies Inc. 067X-0X Manuale Utente
ZDW120 Instructions
P/D 100504
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
0671-01
1
Radio Frequency Controlled, 600W, 120 VAC,
Two Wire Wall Mounted Dimmer Switch
ZDW120
ZDW120 WALL MOUNTED DIMMER
The ZDW120 Wall Mounted Dimmer is a component of the HomePro lighting control system. Wire the Wall
Mounted Dimmer in place of the standard wall switch according to the diagram above and program from the
Wireless Controller to operate loads. Inclusion of the ZDW120 Wall Mounted Dimmer on the ZTH100 Wireless
Controller menu allows remote ON/OFF control and dimming of light connected.
This Wall Mounted Dimmer is designed to work with other HomePro lamp and appliance controls. Z-Wave nodes
of other types can be added to the system and will also act as repeaters if they support this function of repeating
the signal received to other modules in the system.
As part of a HomePro network, the ZDW120 will also act as a wireless repeater to insure that commands intended
for another device in the network are received. This is useful when the device would otherwise be out of the radio
range of the wireless controller.
There are no field repairable assemblies on this unit. If service is needed, the unit must be returned where
purchased.
CAUTION! Read and understand these instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the United States, or the Canadian Electrical
Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation.
To reduce the risk of overheating and possible damage to other equipment, do not install to control a
receptacle, a motor operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance, but
only permanently installed incandescent lamp fixtures. Make sure the lamp(s) to be controlled directly from the
dimmer switch total no more than 600 watts. Retain instructions for future use.
Mounted Dimmer in place of the standard wall switch according to the diagram above and program from the
Wireless Controller to operate loads. Inclusion of the ZDW120 Wall Mounted Dimmer on the ZTH100 Wireless
Controller menu allows remote ON/OFF control and dimming of light connected.
This Wall Mounted Dimmer is designed to work with other HomePro lamp and appliance controls. Z-Wave nodes
of other types can be added to the system and will also act as repeaters if they support this function of repeating
the signal received to other modules in the system.
As part of a HomePro network, the ZDW120 will also act as a wireless repeater to insure that commands intended
for another device in the network are received. This is useful when the device would otherwise be out of the radio
range of the wireless controller.
There are no field repairable assemblies on this unit. If service is needed, the unit must be returned where
purchased.
CAUTION! Read and understand these instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the United States, or the Canadian Electrical
Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation.
To reduce the risk of overheating and possible damage to other equipment, do not install to control a
receptacle, a motor operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance, but
only permanently installed incandescent lamp fixtures. Make sure the lamp(s) to be controlled directly from the
dimmer switch total no more than 600 watts. Retain instructions for future use.
INSTALLATION
CAUTION! - SHOCK HAZARD. Make all connections with the POWER OFF to avoid injury to the installer or damage
to the device.
1. Strip 3/4" of insulation from the ends of the conductors (if not already done) and make connec-
tions as shown in the Wiring Diagram. Note that the line side of the load must be switched.
2. Check connections to be sure they are tight and no bare conductors are exposed.
3. Make sure the load or installation does not exceed the device rating.
4. Install into an appropriately sized electrical wall box. Scored tabs on both sides can be bent up
3. Make sure the load or installation does not exceed the device rating.
4. Install into an appropriately sized electrical wall box. Scored tabs on both sides can be bent up
and down their length with pliers to break off, to allow fitting in a variety of electrical box types.
5. Restore the power.
HomePro
RF Home Automation
Supplied with decorative
switch plate