Advanced Control Technologies Inc. 06X7-0X Manuale Utente
ZDP100 Instructions
071202
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
1
Radio Frequency Controlled, Plug-In, 300W, 120 VAC,
Lamp Module
ZDP100
HomePro
RF Home Automation
ZDP100 PLUG-IN LAMP MODULE
The ZDP100 plug-in Lamp Module is a component of the HomePro lighting control system. Plug the Lamp Module
into a wall outlet and plug a lamp into the Lamp Module. Inclusion of the Lamp Module on the ZTH100, RF Remote
Transmitter menu allows remote ON/OFF control and dimming of lamps connected.
into a wall outlet and plug a lamp into the Lamp Module. Inclusion of the Lamp Module on the ZTH100, RF Remote
Transmitter menu allows remote ON/OFF control and dimming of lamps connected.
This plug-in Lamp Module is designed to work with other HomePro lamp and appliance controls. Z-Wave nodes of
other types can be added to the system and will also act as repeaters if they support this function of repeating the signal
received to other modules in the system.
other types can be added to the system and will also act as repeaters if they support this function of repeating the signal
received to other modules in the system.
As part of a HomePro network, the ZDP100 can act as a wireless repeater to insure that commands intended for
another device in the network are received. This is useful when the device would otherwise be out of the radio range
of the remote controller.
another device in the network are received. This is useful when the device would otherwise be out of the radio range
of the remote controller.
INSTALLATION
Plug this Lamp Module into the wall outlet near the lamp to be controlled, and plug the lamp into the Lamp Module.
Follow instructions in section 4.2.1 of the Remote Transmitter Operating instructions to add this module under the
control of the Remote Transmitter. Make sure the lamp(s) to be controlled total no more than 300 watts. WARNING:
Plugging a non-resistive load such as florescent lighting or a device with a motor may result in damage to the Lamp
Module and will void the warranty.
Follow instructions in section 4.2.1 of the Remote Transmitter Operating instructions to add this module under the
control of the Remote Transmitter. Make sure the lamp(s) to be controlled total no more than 300 watts. WARNING:
Plugging a non-resistive load such as florescent lighting or a device with a motor may result in damage to the Lamp
Module and will void the warranty.
Lamp Module Button
The Lamp Module has a button on the face (see picture above) that switches an attached lamp ON and OFF, and
adjusts its dimming level by holding it down, and it is also used to configure the module to operate from the remote
transmitter. With the Remote Transmitter, the Lamp Module can be switched ON and OFF, and can be included
in groups of lights (a group can also be a single module) that operate at the same time, and in scenes that set a
lighting mood.
adjusts its dimming level by holding it down, and it is also used to configure the module to operate from the remote
transmitter. With the Remote Transmitter, the Lamp Module can be switched ON and OFF, and can be included
in groups of lights (a group can also be a single module) that operate at the same time, and in scenes that set a
lighting mood.
Switch power ON and OFF
When the button is pressed and released quickly, the power will toggle. This means that power will be turned OFF
if it was ON and turned ON if it was OFF. When switching the Lamp Module ON or OFF, the light will dim UP (or
DOWN) in approximately 2 seconds until the final level is reached.
if it was ON and turned ON if it was OFF. When switching the Lamp Module ON or OFF, the light will dim UP (or
DOWN) in approximately 2 seconds until the final level is reached.
Dimming
If the button is constantly pressed the light will be dimmed. The dimming function will also toggle. Constantly
pressing the button the Lamp Module will dim either UP or DOWN until it reaches the maximum or minimum value.
The second time the button is held down, the dimming will change direction. When the power level reaches either
full power or minimum power the dimming will stop until the button has been released and is pressed again.
pressing the button the Lamp Module will dim either UP or DOWN until it reaches the maximum or minimum value.
The second time the button is held down, the dimming will change direction. When the power level reaches either
full power or minimum power the dimming will stop until the button has been released and is pressed again.
Button functions
1. Adds module under the control of Remote Transmitter.
2. Local ON and OFF (push and release).
3. Local dimming (hold down).
2. Local ON and OFF (push and release).
3. Local dimming (hold down).