Advanced Control Technologies Inc. 0778-0X Manuale Utente
Z-Wave ZDP100 Instructions, Series 300, Release 4.1
052909
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
0778-01
1
Z-Wave Radio Frequency (RF) Controlled, 300W, 120 VAC,
Plug-In Lamp Module, Series 300, Release 4.1
ZDP100
HomePro
RF Home Automation
Button functions
1. Use to include module under the command of a Controller.
2. Local ON and OFF (push and release).
3. Local dimming (hold down).
2. Local ON and OFF (push and release).
3. Local dimming (hold down).
ZDP100 PLUG-IN LAMP MODULE
The ZDP100 plug-in Lamp Module is a component of the HomePro lighting control system. Plug the Lamp Module
into a wall outlet and plug a lamp into the controlled outlet of the Lamp Module. Inclusion of the ZDP100 Lamp Module
on the ZTH100 Wireless Controller menu allows remote ON/OFF control and dimming of lamps connected.
into a wall outlet and plug a lamp into the controlled outlet of the Lamp Module. Inclusion of the ZDP100 Lamp Module
on the ZTH100 Wireless Controller menu allows remote ON/OFF control and dimming of lamps connected.
This plug-in Lamp Module is designed to work with other Z-Wave enabled devices. Z-Wave nodes of other types can
be included in the system and will also act as repeaters if they support this function of repeating the signal received
to other modules in the system.
be included in the system and will also act as repeaters if they support this function of repeating the signal received
to other modules in the system.
This product supports 40Kbps data transmission. This product can also be used for networking support in
systems that stream metadata. An example might include transmission of information from audio devices such as
song title, artist, and album information to various displays around the home.
systems that stream metadata. An example might include transmission of information from audio devices such as
song title, artist, and album information to various displays around the home.
As part of a Z-Wave network, the ZDP100 can act as a wireless repeater to insure that commands intended for another
device in the network are received. This is useful when the device would otherwise be out of the radio range of the
wireless controller.
device in the network are received. This is useful when the device would otherwise be out of the radio range of the
wireless controller.
INSTALLATION
Plug this Lamp Module into the wall outlet near the lamp to be controlled, and plug the lamp into the Lamp Module. Make
sure the lamp(s) to be controlled total no more than 300 watts. To reduce the risk of electric shock, this product has a
grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type power outlet. If the plug
does not fit into the outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
sure the lamp(s) to be controlled total no more than 300 watts. To reduce the risk of electric shock, this product has a
grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type power outlet. If the plug
does not fit into the outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
WARNING: Plugging a non-resistive load such as florescent lighting or a device with a motor may result in damage
to the Lamp Module and will void the warranty. Note: Grounded outlet is always powered and can be used for any
other appliance. See the ZTH100 or other Wireless Controller operating instructions for details to include this module
under the command of the Wireless Controller.
to the Lamp Module and will void the warranty. Note: Grounded outlet is always powered and can be used for any
other appliance. See the ZTH100 or other Wireless Controller operating instructions for details to include this module
under the command of the Wireless Controller.
INCLUDING ZDP100 TO THE NETWORK
STEP 1.. Prepare the Controller to include a unit to the network by adding it to a group (method of adding a
node to the network). Refer to controller instructions.
STEP 2. The ZDP100 must be in its permanently installed location. Tap the button on the ZDP100 once.
STEP 3. You should see an indication on your Controller that the “DEVICE WAS INCLUDED” in the network.
NOTE: If you have trouble adding the ZDP100 to a group it may be that the Home ID and Node ID were not
cleared from it after testing. You must first “RESET UNIT” with your controller to remove it from the network.
If using the ZTH100 select “SETUP” and scroll to “RESET UNIT”. Although adding it to a group includes it in
the network, removing it from a group does not remove it from the network. If removed from a group, it just
functions as a repeater.
cleared from it after testing. You must first “RESET UNIT” with your controller to remove it from the network.
If using the ZTH100 select “SETUP” and scroll to “RESET UNIT”. Although adding it to a group includes it in
the network, removing it from a group does not remove it from the network. If removed from a group, it just
functions as a repeater.
• This product supports Zensor Net Beam technology.
Note: This module must be “Included in the
Network” only where it will be permanently
installed. You cannot “test bench” configure this
module, then install. The proper operation of this
node in the mesh network is dependent on it
knowing its location with respect to other nodes.
Network” only where it will be permanently
installed. You cannot “test bench” configure this
module, then install. The proper operation of this
node in the mesh network is dependent on it
knowing its location with respect to other nodes.